background image

13

GB

• n. 1 bag with screws for fixing the frame to the ceiling-buttress 

1

• n. 1 bag with screws for fixing the chimney stack to the hood canopy 

2

• n. 1 bag with screws for fixing the connection box 

3

• n. 1 bag containing documents.

Instructions  for  installation

To facilitate installation, proceed in the order indicated below:

• Installing the Frame.
• Ducting or recirculation fitting.
• Connection to the mains power supply.
• Fitting the telescopic chimney.
• Electrical connection and testing.
• Fitting the hood canopy

Installing  the  Frame

The frame is suitable for fixing to the ceiling or to a
wooden  buttress  of  suitable  thickness,  which    must
be firmly anchored to the ceiling or to other bearing
structures.

• Using a plumb line or similar tool, identify and mark

the centre on the ceiling or buttress, starting from the
centre of the cooking appliance.

• Use  the  cardboard  template  provided  to  mark  the

ceiling  or  wooden  buttress,  making  sure  that  the
centres coincide and lining up one of the two axes (A
or B) of the template so that it is parallel with the long
side of the cooking appliance.

• Mark  the  position  of  the  4  fixing  holes  indicated  on

the drilling template.

• Drill the holes as follows:
- Ceiling: 4 holes Ø 10 mm to fix the frame in position;
- Buttress: 4 holes Ø 8 mm to fix the frame in position.

Fixing  to  the  Ceiling

Attention: Due to the many differing types of ceiling
construction,  the  choice  of  fixings  is  left  to  the
discretion of the installer.  It is necessary to emphasise
that the fitting has to be absolutely accurate because
of the weight of the cooker hood and because of the
flexing  caused  by  accidental  lateral  stresses  on  the
appliance.  Only  the  following  types  of  ceiling  are
suitable for installing the Island cooker hood:

• Solid concrete ceiling: use dowels for concrete, not supplied.
• Solid wooden buttress ceiling: use Ø 10 mm wood screws with a minimum length of 120

mm, not supplied.

• Cavity ceiling with inner space, having a wall thickness of about 20 mm; use, in this case

only, the 4 dowels and screws supplied in bag (1).  Once fixed, make sure that the base
is absolutely stable, even when the metal frame is subjected to lateral stress.  In all other

TS

TI

4324665 01 - 001201

Summary of Contents for ZHC 941












Reviews: