background image

15

GB

Installation  instructions

For easy installation, proceed as follows:

• Fix the wall brackets and Splashback
• Fix the canopy
• Connect the hood to the mains power supply and make sure that it works properly
• Set the hood for ducting or recirculation
• Fix the telescopic chimney

Fitting  the  wall  brackets  and  Splashback

Please refer to (

fig.2a-b

):

Draw

  a  vertical  line  on  the

wall,  from  the  centre  of  the
cooking appliance up to the
ceiling, using a marking pen.
This is to ensure the correct
vertical  alignment  of  the
various parts.

• Fixing  the  wall  brackets

item  2:

a)

Place

 one of the brackets 

2

against 

the 

wall

approximately  1  or  2  mm
from the ceiling or from the
top  limit,  aligning  its  centre
(slot) with the vertical line.

b)

Mark

  the  centres  of  two

keyholes  in  the  bracket  on
the wall.

c)

Rest

  the  other  bracket 

2

against  the  wall,  aligning  it
with  the  vertical  line,  at  a
distance 

X

  measured  as

shown in 

fig. 2

 equal to the height of the upper chimney element 

S

 supplied with the

hood. The position 

X

 may vary, according to the various sizes of upper chimney element

available.

d)

Mark 

the centres of the keyholes in the bracket on the wall.

• Drilling  fixing  holes  item  1:

a)

Mark

 a point on the vertical line at a distance from the cooking appliances of:

d

 =970 min (distance without splashback).

d

  =height  of  splashback  +  320  mm  (distance  with  splashback).The  distance 

H

  is  the

minimum height in mm from the cooking appliances to the bottom edge of the front panel
of the hood.

b) At the point marked, draw a horizontal line parallel to the cooking appliances.
c)

Drill

 two holes in the wall 

1

 using an 8 mm drill bit (fig.2a ), and insert the rawl plugs and

screws into the holes 1 (4.2 x 44.4 screws). Fix the screws, leaving a space of 5-6 mm

232

260

1

1

2

260

1

1

20

X

H min 650

d = 970 min

Fig. 2

a

b

Summary of Contents for ZHC 94












Reviews: