background image

Problem and alarm code

Possible cause and solution

The program lasts too long.

• If the delayed start option is set, cancel the delay setting or wait

for the end of the countdown.

The remaining time in the dis-

play increases and skips nearly

to the end of program time.

• This is not a defect. The appliance is working correctly.

Small leak from the appliance

door.

• The appliance is not level. Loosen or tighten the adjustable feet

(if applicable).

• The appliance door is not centred on the tub. Adjust the rear

foot (if applicable).

The appliance door is difficult

to close.

• The appliance is not level. Loosen or tighten the adjustable feet

(if applicable).

• Parts of the tableware are protruding from the baskets.

Rattling/knocking sounds from

inside the appliance.

• The tableware is not properly arranged in the baskets. Refer to

basket loading leaflet.

• Make sure that the spray arms can rotate freely.

The appliance trips the circuit-

beaker.

• The amperage is insufficient to supply simultaneously all the ap-

pliances in use. Check the socket amperage and the capacity

of the meter or turn off one of the appliances in use.

• Internal electrical fault of the appliance. Contact an Authorised

Service Centre.

Refer to "Before first use""Daily

use", or "Hints and tips" for other

possible causes.

Once you have checked the appliance, deactivate

and activate the appliance. If the problem occurs

again, contact an Authorised Service Centre.

For alarm codes not described in the table, contact

an Authorised Service Centre.

THE WASHING AND DRYING RESULTS ARE NOT SATISFACTORY

Problem

Possible cause and solution

Poor washing results.

• Refer to "Daily use""Hints and tips" and basket loading

leaflet.

• Use more intensive washing programmes.

• Clean spray arm jets and filter. Refer to "Care and Clean-

ing".

Poor drying results.

• Tableware has been left for too long inside a closed appli-

ance.

• There is no rinse aid or the dosage of rinse aid is not enough.

Set the rinse aid dispenser to a higher level.

• Plastic items may need to be towel dried.

• For the best drying performance activate the option XtraDry.

• We recommend to always use rinse aid, even in combination

with multi-tablets.

16

Summary of Contents for ZDT26011FA





















Reviews: