background image

Problem and alarm code

Possible cause and solution

The program lasts too long.

• If the delayed start option is set, cancel the delay

setting or wait for the end of the countdown.

Small leak from the appliance door.

• The appliance is not levelled. Loosen or tighten the

adjustable feet (if applicable).

• The appliance door is not centred on the tub. Adjust

the rear foot (if applicable).

The appliance door is difficult to close.

• The appliance is not levelled. Loosen or tighten the

adjustable feet (if applicable).

• Parts of the tableware are protruding from the bas-

kets.

Rattling/knocking sounds from inside the

appliance.

• The tableware is not properly arranged in the bas-

kets. Refer to basket loading leaflet.

• Make sure that the spray arms can rotate freely.

The appliance trips the circuit-beaker.

• The amperage is insufficient to supply simultaneous-

ly all the appliances in use. Check the socket am-

perage and the capacity of the meter or turn off one

of the appliances in use.

• Internal electrical fault of the appliance. Contact an

Authorised Service Centre.

Refer to "Before first use""Daily

use", or "Hints and tips" for other

possible causes.

Once you have checked the appliance, deactivate

and activate the appliance. If the problem occurs

again, contact an Authorised Service Centre.

For alarm codes not described in the table, contact

an Authorised Service Centre.

THE WASHING AND DRYING RESULTS ARE NOT SATISFACTORY

Problem

Possible cause and solution

Poor washing results.

• Refer to "Daily use""Hints and tips" and basket loading

leaflet.

• Use more intensive washing programmes.

• Clean spray arm jets and filter. Refer to "Care and Clean-

ing".

Poor drying results.

• Tableware has been left for too long inside a closed appli-

ance.

• There is no rinse aid or the dosage of rinse aid is not enough.

Set the rinse aid dispenser to a higher level.

• Plastic items may need to be towel dried.

• For the best drying performance activate the option XtraDry

and set AirDry.

• We recommend to always use rinse aid, even in combination

with multi-tablets.

14

Summary of Contents for ZDT24004FA





















Reviews: