background image

 

5

 

Door reversibility 

 

(Fig. 3)

Unplug the refrigerator from the wall socket before 
performing the following operations:

Remove socle (2) by unscrewing its front screws. 
Slide it downwards to release it from the central 
runners.

Remove bottom hinge (1).

Unscrew pin (C) from hole (A) and screw it into hole 
(B).

Remove door stop hinge (D) and refit it on the 
opposite side.

Slide out the lower door from middle hinge.

Remove middle hinge (4) and upper hinge (3) and 
refit them on the opposite side.

Refit lower door and bottom hinge (1) on the 
opposite side.

Turn the base upside-down and refit it.

Remove handles (5-6) and refit them on the opposite 
side.

The holes that are not used are to be masked with 
the plastic plugs removed.

 

Attention

 

After completion of the door reversibility operation, 
verify that the door gasket is adherent to the 
cabinet. If the ambient temperature is cold (i.e. in 
Winter), the gasket may not fit perfectly to the 
cabinet. In that case, wait for the natural fitting of 
the gasket or accelerate this process by heating up 
the part involved with a normal hairdrier.

 

Fig. 3

D158

5

6

3

4

D
C
A

1

B

2

Summary of Contents for ZC320D










Reviews: