background image

13

Note: Ensure that the wall bracket is levelled
using a spirit level. The hood can be aligned
or adjusted in height by rotating the
adjustment screw.

3.

Mark on the wall the centres of the two keyholes
of the bracket.

4.

Fix wall bracket (2) to the wall at about 1-2 mm
from  the  ceiling  or  from  the  maximum  height
required, paying attention to the correct vertical
alignment.

5.

Mark on the wall the centres of the two keyholes
of the bracket.

6.

Fix wall bracket (3) to the wall paying attention to
the  correct  vertical  alignment  at  a  ‘X’  distance
measured  as  in  Fig  2.  The  ‘X’  distance  being
equal  to  the  upper  section  (S),  it  can  vary
according  to  the  different  height  of  this  section
needed to suit the ceiling height.

7.

Mark on the wall the centre of the two keyholes
of the bracket.

8.

Pilot drill all the holes positions as marked on the
wall using 8mm drill. Fix the wall brackets (1,2,3)
using the 8mm rawlplugs and screws supplied.

Fitting the Canopy

1.

Rotate halfway the two screws (R) positioned on
the hanging lugs of the canopy.

2.

Hook  the  canopy  on  to  the  wall  bracket  (1)
ensuring that the two lugs of the bracket are fitted
on  the  keyhole  fixing  points  of  the  canopy  and
push  downwards  as  allowed  by  adjustment
screws.

3.

The canopy can be aligned or adjusted in height
using the two adjustment screws.

4.

Carry out the electrical connection as instructed.
Once  the  electrical  connections  have  been
completed, check the worktop illumination, motor
and motor speeds work properly.

Summary of Contents for CWH 6065

















Reviews: