7
Prior to using for the first time
Before using your dishwasher for the first time:
1. Ensure that the electrical and water connections comply
with the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and then fill
with dishwasher salt
5. Fill the rinse aid dispenser
The water softener
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these minerals and salts, the harder
your water is.
Water hardness is measured in equivalent scales, German
degrees, French degrees and mmol/l (millimol per litre).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
If the water softener has been adjusted on level 1 and no salt
is being used, the salt refill indicator light on the control panel
will always remain illuminated when the machine is switched
on.
Setting the water softener
1. Open the dishwasher door.
2. Remove the lower basket from the dishwasher.
3. Turn the water hardness switch until the required level (see
table) corresponds with the marker .
4. Replace the lower basket.
The dishwasher is factory set
at position 2.
Filling with dishwasher salt
Only use salt specifically designed for use in
dishwashers.
All other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water
softener.
Only fill with salt just before starting one of the complete
washing programmes.
This will prevent any grains of salt or salty water, which
may have been spilt, remaining on the bottom of the
machine for any period of time, which may cause
corrosion.
To fill:
1. Open the door, remove the lower basket and unscrew the
cap of the salt container by turning it anticlockwise.
2. Pour 1 litre of water inside the container (this is necessary
only before filling with salt for the first time).
3. Using the funnel provided,
pour in the salt until the
container is full.
4. Replace the cap making
sure that there is no trace
of salt on the screw
thread or on the gasket.
5. Screw on the cap tightly
turning it clockwise until it
stops with a click.
The salt container will require topping up periodically. You are
reminded of this by the salt indicator light on the control panel
which comes on when the salt has finished.
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been
replenished, assuming the dishwasher remains switched
on. If you are using salts that take longer to dissolve then
this can take longer. The function of the machine is not
affected.
Do not worry if water over flows from the unit when filling with
salt, this is quite normal.
AA08
SALE
ZOUT
SAL
T
SALZ
SEL
SR14
Setting
of the
water
softener
French
degrees
(°TH)
German
degrees
(°dH)
Use of
salt
in mmol/l
(millimol per litre,
international unit for
the hardness of water)
Range
level 5
level 4
level 3
level 2
level 1
level 1
81 - 90
61 - 80
41 - 60
21 - 40
8 - 20
< 8
46 - 50
35 - 45
23 - 34
12 - 22
4 - 11
< 4
8,3 - 8,9
6,3 - 8,2
4,0 - 6,2
2,0 - 3,9
0,7 - 1,9
< 0,7
IV
IV
IV
III
I/II
I
yes
yes
yes
yes
yes
no
Water hardness
