ZANTIA KERA Use And Maintenance Manual Download Page 32

32

Mod. KERA rev 01

Introduction

translated from the original text

EN

•  It is forbidden to operate the product with the door 

open or the glass broken.

•  Do not stay a long time in front of the product while run-

ning. Do not overheat the room where

 you stay or where 

the product is installed. This could harm your physical con-

ditions and cause health issues.

•  The product must be stored in humidity-free rooms and 

not exposed to weather conditions.

•  Do not remove the feet for setting the product body on 

the floor to guarantee proper insulation, especially for 

floors made of flammable materials. 

•  Place a floor protection plate as a base for the product if 

the floor is made of flammable material, such as parquet 

or carpets. (considering that the plate must extend be-

yond the front of the boiler by at least 25/30cm).

•  It is strictly forbidden to use flammable liquids to light 

the fire; the pellets light automatically when the boiler 

is on.

•  Extraordinary maintenance operations must only be car-

ried out by authorised and qualified personnel. 

•  For seasonal use of the boiler, in case of improper draught 

or adverse weather conditions (temperatures < 0°C), make 

sure that the chimney flue is perfectly insulated and not 

obstructed to avoid freezing and any backflow of flue gas.

•  If the flue catches fire, immediately switch off the product

unplug it and never open the door. Then call the compe-

tent authorities.

•  As the product has an air consumption necessary for com-

bustion, it is recommended to connect the product to the 

outside by means of suitable piping reaching the specific 

inlet at the back of the boiler.

•  For safety purposes, it is recommended to maintain at least 

20 cm between the hot sides of the boiler and any flam-

mable cover materials (e.g. matchboarding walls, wallpa-

per etc.) or to use specific insulating materials available on 

the market. This assessment must also be made regarding 

furniture, armchairs, curtains and similar objects. 

•  To facilitate technical support interventions, do not recess 

the product in tight spaces, do not push it against the wall 

as this could jeopardize correct ventilation.

•  The absence of draught by the flue (or, for example, the 

obstruction or closing of the brazier air inlet or of the 

brazier itself) alters the operation of the boiler which, 

during the automatic ignition phase, could cause too 

many pellets to be dispensed into the brazier due to 

delayed ignition of the fire.

•  The pellets feeding the product must have the characteris-

tics described in this manual.

•  Do not leave children alone near the boiler while it is lit, as 

all the hot parts could cause serious burns.

•  Do not carry out any operation on the boiler other than 

those indicated for its regular use or those recommended 

in this manual to solve simple problems. Always unplug 

the appliance before intervening and only operate with 

the boiler cold. 

•  IT IS absolutely prohibited to remove the pellet tank pro-

tective grid.

•  Always check and make sure that the door of the combus-

tion chamber is hermetically closed during ignition and 

operation of the boiler.

•  Automatic ignition of the pellets is the most delicate 

phase. It is recommended to always keep the product and 

brazier clean so that it can be done without any problems.

•  In the presence of operating faults, the product can only 

be switched back on after having solved the cause of the 

problem.

•  ZANTIA Climatização S.A. is not liable for inconvenience, 

tampering with, damage, or whatsoever due to failure to 

comply with the provisions provided in this manual.

•  This booklet is an integral part of the appliance; therefore, 

it must be stored and accompany the device in case of 

transfer of property.

•  This appliance is not intended for use by persons (includ-

ing children) with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, unless 

they have been given supervision or instruction concern-

ing use of the appliance by a person responsible for their 

safety.

•  Only use the fuel recommended by the manufacturer. The 

product cannot be used as an incinerator. It is strictly 

forbidden to use liquid fuels.

•  To correctly use the product and the electronic equipment 

connected to it and to prevent accidents, always observe 

the indications provided in this manual.

•  Before starting any operation, the user or whoever is op-

erating the product must have fully read and understood 

this installation and use manual. Errors or improper set-

tings can cause dangerous conditions and/or irregular 

operation.

•  Switch the product off in case of failures or malfunction-

ing.

•  The buildup of unburned pellets in the burner after 

each "failed ignition and alarm" must be removed 

before attempting another ignition. Check that the 

burner is clean and well positioned before switching 

it back on.

•  Do not wash the product with water. Water could infiltrate 

into the unit and damage the electric insulations, causing 

electrical shocks.

•  Install the product in rooms which are not fire hazards and 

are set up with all services such as supplies (air and elec-

tric) and flue gas exhausts. 

•  Do not stand on the product or use it as a support struc-

ture.

•  Do not dry sheets on the product. Drying racks or similar 

products must be kept a safety distance from the product. 

There is the risk of fire!

•  All responsibility for the improper use of the product is 

fully borne by the user and releases the manufacturer 

from all civil and criminal liability.

•  In case of failure to the ignition system, do not force igni-

tion by using flammable materials.

1.5 

WARRANTY TERMS AND CONDITIONS

1.  The Manufacturing Company guarantees the structure 

and materials making up the product for a period of 24 

months from the date of purchase, as long as the pur-

chaser sends the attached sheet within 8 days of the 

date of delivery, completely filled out and keeps a copy 

as a proof of purchase. This warranty is valid as long as:

a)  The purchaser has installed the product in compliance 

with standards in force,

Summary of Contents for KERA

























































































Reviews: