Zanotti Zero Series Installation Manual Download

Page: 67 / 78

Refrigeration unit

Series Zero Direct-Drive

Z200 | Z250 | Z350 | Z380

Z380 Multi

INSTALLATION MANUAL

rev.01

3.18 Liquid injection valve kit (optional)

3.18.1 Operating logic

In order to reduce the exhaust temperature of the Road compressor, the liquid injection valve injects liquid

into the suction line.

As soon as the compressor discharge temperature reaches 100°C (230°F), the thermostat installed on

the compressor discharge line opens the injection valve to lower the exhaust temperature and protect the

Road compressor.

Figure 73 - Liquid injection valve

3.18.2 Components

•

Liquid injection solenoid assembly

•

Reel

•

Plugs and connectors for assembling and connecting new parts

•

Thermostat

3.18.3 Installation

Follow the instructions in the installation manual OIST062 for assembly.

Summary of Contents for Zero Series















































































Search results

Summary of Contents for Zero Series

Reviews:

Related manuals for Zero Series

Brands by name

Popular brands

Zanotti Zero Series, Installation Manual

Search results

Summary of Contents for Zero Series

Reviews:

Related manuals for Zero Series

Brands by name

Popular brands