Storing a Speed Dial
Dialgizmo can store up to 6 separate speed dial numbers. Each number
can be up to 16 digits long. To store a new speed dial number, follow the
steps below:
Step 1: To store a speed-dial
number, Pick up the phone then
dial 0 and hold for 2 seconds,
then release. You will hear 3 quick
beeps to indicate that it is ready to
store a new speed-dial number.
Step 2: Next dial the location in
which you wish to store the
speed-dial number, then release.
Valid locations are 3, 4, 5, 6 ,7
and 8. You will hear 2 quick
beeps to set you know that it is
ready to store the number.
Note: 4 beeps means a bad location was
selected. Valid locations are: 3,4,5,6,7 and 8.
Step 3: Now just dial the number
to be stored. After each digit, you
will hear a quick beep to let you
know the number has been
saved. You can store up to 16
digits in each speed-dial location.
Step 4: When you have finished
dialing the number, just hang up
the phone. This completes the
storing of the speed-dial number.
To delete a speed-dial number, just follow steps 1 and 2 above, then
hang up the phone. The selected speed-dial location is now cleared.
There is no need to clear a speed-dial location before saving a new
number in that location.
Troubleshooting
Dialgizmo should provide trouble free operation, however if something
does go wrong….
Symptom
Problem
Three sets of 3 beeps are heard
when the phone is picked up:
beep-beep-beep …
beep-beep-beep …
beep-beep-beep …
Dialgizmo was not able to self adjust
to the voltages on your phone line.
This means that the dial-hold features
will not be available with this
combination of line and telephone.
This happens in some rare cases
where the line voltage is very low or
the line current is in excess of 60mA.
You will need to disable the dial-hold
features by turning ON switch 1, see
section 6 for details. Dialgizmo will
still perform basic pulse to tone
conversion in this mode.
No DTMF tone are heard when a
number is dialed on the rotary dial is
dialed.
If Dialgizmo has just been installed,
then wait 30 seconds for the line
voltage to stabilize before continuing.
Last Number Redial is not saved
The recently dialed number is stored
into the Last Number Redial location
by Dialgizmo when no new digit has
been dialed for about 10 seconds.
For more additional support, see the Dialgizmo website at
http://www.dialgizmo.com or email [email protected]
Changing the Dial Settings
There are some options on Dialgizmo that can be changed by opening the case
and changing the switch settings. To open the case, first disconnect from the
phone and line, then insert a small screw driver or flat blade into the slot and twist
as shown below. You will expose the circuit board and note the small set of 4
switches as per the diagram below:
Off
(Factory default mode)
On
Switch 1
– Dial Hold
Dial-Hold features enabled
Dial-Hold features disabled
Switch 2
– Reserved
Leave Off
N/A
Switch 3
– Zero Position
Zero is at far end of dial
Zero is at near end of dial
Switch 4
– Digit Order
Ascending
Descending
Different dial layouts
Throughout the world there are several different types of dial layout for rotary
phones. Although rare, they do exist, and if you are lucky enough to have one of
these rare types, then you will need to change the dip switches inside of Dialgizmo
in order to get correct dialing.
Type A
Default mode
Type B
Type C
Type D
Switch 3: Off
Switch 4: Off
Switch 3: On
Switch 4: Off
Switch 3: Off
Switch 4: On
Switch 3: On
Switch 4: On
NOTE: The relative positions of the dial-hold functions do not change, so for example Last
Number Redial is accessed by dialing 9 in Type A, 8 in Type B, 1 in Type C and 2 in Type D.
Specifications
IMPORTANT NOTE: Dialgizmo has been specifically designed for
use on VoIP services, while VoIP telephone services use similar
currents and voltages to standard telephone lines, Dialgizmo is not
approved for connection to standard PSTN telephone lines!
Phone line environment
On hook line voltage …………...… 18v to 65v
Off hook line current ……………… 7mA to 60mA
Ringing voltage …………………… max 250v
Dialgizmo
Power supply ……………………… Line powered
Line current draw (on hook) …….. Approx 100nA
Line current draw (off hook) …….. Approx 5mA
Operating temperature …………... 5°C to 35°C
Ringing pass-through ……………. 2 REN
For more information see the Dialgizmo website at:
http://www.dialgizmo.com
Manufactured by:
Zanikan Pty Ltd
PO Box 502
Collins Street West
Melbourne, VIC 8007
Australia
Phone: +61 3 9946 5400
Fax: +61 3 9946 5450
Manual revision 1.06 – April 2009
