FUNCTIONING, MOUNTING
APPLICATION
By pressing the button, the transmitter sends a signal with 868,32 MHz
frequency which controls EXTA FREE receivers.
Device programming
procedure (adding a transmitter to a receiver’s memory) is described in
particular EXTA FREE manual instructions.
The device range (up to 250 m
depending on a receiver) can be increased by means of a retransmitter or few
RTN-01 retransmitters.
BATTERY CHANGE
Battery discharge status is signalled by several LED red diode flashes
during transmission time.
1. Remove the upper cover of the transmitter - to do it lever up four latches at
the bottom of the push-button removing the cover at the same time.
2. By means of a screwdriver remove the battery from the latch.
3. Mount a new battery.
Watch battery polarisation marked on the latch. Wrong battery mounting
may cause device damage.
4. Put the spring on the push-button (it is important that the smaller spring diameter secured with
insulation leans against the push-button).
5. Put back the upper cover by placing the latches of the cover straight into their base and snap it.
CAUTION: While changing the battery, it is suggested to press any of the buttons for about
5 seconds before putting it into a latch. Next press transmission button several times to check its
operation. If the transmitter does not work properly repeat the battery change procedure.
Radio foot transmitter RNL-01 controls
operation of RWL-01 radio lighting switch
(switch on / switch off) or RDP-01 radio
dimmer (switch on / switch off,
light brightening / dimming).
The receivers can be controlled by 4-channel
button radio transmitter RNK-04. The RNL-
02 transmitter does not require additional
installation, external power supply connection
and mounting.
COOPERATION AND OPERATING RANGE
Symbol
ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01
RNK-02
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNK-04
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
P-256/8
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
P-257/4 (2)
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNM-10
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
RNP-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNP-02
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNL-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
RTN-01
200 m
200 m
200 m
200 m
200 m
250 m
200 m
250 m
250 m
200 m
250 m
RCR-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
RTI-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RXM-01
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
* - 1-channel transmitters do not cooperate with roller blind controllers.
CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between
a transmitter and a receiver, it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %,
reinforced concrete: from 40 to 80 %, metal: from 90 to 100% , glass: from 10 to 20 %. Over- and underground medium and high electrical power lines,
radio and television transmitters, GSM transmitters set close to a device system have also a negative influence on the range.
WARRANTY CARD
There is 24 months guarantee on the product
1. ZAMEL provides a two-year warranty for its products.
2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances
b) defects resulting from incorrect installation or operation of ZAMEL products; c) defects resulting from any changes made by CUS-
TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold; d) defects resulting
from force majeure or other aleatory events for which ZAMEL is not liable; e) power supply (batteries) to be equipped with a device
in the moment of sale (if they appear);
3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect.;
4. ZAMEL will review complaints in accordance with existing regulations.;
5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL.
6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy
between the goods and the contract.
Salesman stamp and signature, date of sale
The ZAMEL company devices
which are characterised
with this sign can cooperate
with each other.
