MOTION SENSOR PIR 120/360° miniature
with a probe, IP65 on the MCR-08 conductor
USER MANUAL
ZAMEL Sp. z o.o.
ul. Zielona 27, 43-200 Pszczyna, Poland
Tel. +48 (32) 210 46 65, Fax +48 (32) 210 80 04
www.zamel.com, e-mail: [email protected]
plik: mcr-08_inst_ext_gb | modyfikacja: 14.05.2020
APPEARANCE
FEATURES
DESCRIPTION
NOTE
• Detection angle 360 / 120 degrees
• Selectable detection area: 3 m / 6 m
• Light on time setting: 5s, 30s, 1 min., 3 min.,
5 min., 8 min.
• Adjustment of the in-built light sensor 10 lux /
2000 lux
• Miniature design of the device facilitates its
installation in different places
• Hermetic probe on the cable can be used to
adapt the device to different applications.
The MCR-08 miniature motion sensor is
designed for automatic light control or for con-
trolling any other electric receiver. Its design is
based on a state of the art infrared (PIR) motion
detector system. The device detects motion in
the monitored area within the radius of ca. 3 or
6 m, within 120° / 360° around the sensor. The
device was designed to miniaturize the detec-
tor’s electronic part and to enable its operation
with the use of an external, hermetic sensor
(IP54) mounted on a cable. The condition of
external light intensity is additionally verified. If
the device detects motion and the light intensity
level is below the setting value, the sensor will
turn the light on and start to count the preset
time, after which the light will be automatically
turned off. The device includes a set of switches
for simple and repeatable setting and adjust-
ment. This facilitates the installation of devices
in the case of larger systems. Thanks to its spe-
cific design and operation, the sensor provides
optimal control over the energy flow, optimizing
the costs of illuminating communication routes,
stairs, toilets and facilities, etc. The design of
the device’s mechanics facilitates the installa-
tion of the sensor directly in a suspended ceil-
ing and in drywall. It is also possible to adapt
the device to fit in a junction box, where the
cable probe will monitor the preset area after it
is led out and fixed in a desired place under the
equipment cover.
Read this User Manual carefully before connecting and operating the device. The device must be installed by a qualified electrician. Connect this product
to a single-phase power system according to applicable standards. See this Manual for the wiring instructions. The activities related to the installation, con-
nection and adjustment should be performed by qualified electricians, familiar with the User Manual and functions of the device. Do not open or otherwise
disassemble the product enclosure; otherwise the product warranty will be void and an electrocution hazard may occur. Prior to installing and wiring this
product, make sure that the wiring to be connected is not live. The conditions and methods of transport, storage and operation of this product may affect its
performance. Do not install the products if any of its components are missing, the product is damaged or deformed in any way. If any malfunctions are found,
consult the manufacturer. The manufacturer is not be liable for any damage resulting from improper installation or operation of the device. Any repairs or
modifications made independently will void the warranty. Since the technical data are subject to constant modifications, the Manufacturer reserves the right
to change the product characteristics and introduce other design solutions for the device.
TECHNICAL DATA
Power supply voltage: 230 V AC
Voltage frequency: 50 Hz
Motion detection angle: 120 / 360 degrees
Maximum effective zone: 3 lub 6 m (selectable)
Time to turn on the lighting: 5s, 30s, 1 min, 3 min, 5 min, 8 min
Time measurement accuracy: ± 15 % of the selected value
Scope of light sensor settings: 10 ÷ 2000 lux
Acceptable load:
Traditional bulbs: 800 W
Fluorescent tubes: 200 W
LEDs: 15 W
Power consumption: <0,5W
Installation height: 2 ÷ 4 m
Operating temperature: -20 ÷ + 40
°
C
Permissible humidity: < 93% RH
Dimensions: 55,5 x 55,5 mm
Weight: 0,4 kg
Do not dispose of this device in
the trash can with other waste!
In order to avoid harmful effects
on the environment and human
health, store used device in
specially designated places.
Household electronic waste
can be returned for free and in any amount
to the collection point established for this
purpose, and also to the shop when buying
new equipment.
Motion sensor
Switching devices
Connection
cables
