VER. 003_20.05.2011
RDP-01 oPERAtioN
RDP-01 can operate in five modes:
REMotE CoNtRoLS PRoGRAMMiNG
CoMFoRt
(Available only in coop-
eration with 4 push-button
transmitter). In this mode
the following two functions
are realised:
oNE PuSH-ButtoN
Pressing the programmed
push-button shortly (<0.8
sec.) causes the dimmer
to operate in the range
of switch on/switch off (to the last
adjustment of lighting luminous den-
sity level), however pressing the pro-
grammed push-button longer (>0.8
sec.) causes alternate lighting bright-
ening - dimming.
tWo PuSH-ButtoN
SWitCH oN
push-button:
pressing the programmed
push-button shortly (<0.8
sec.) causes the lighting
switches on (the last adjustment of
lighting luminous density level), how-
ever pressing the programmed push-
button longer (>0.8 sec.) causes light-
ing brightening (to the maximum level).
SWitCH oFF
push-button:
pressing the programmed
push-button shortly (<0.8
sec.) causes the light-
ing switches off, however
pressing the programmed push-but-
ton longer (>0.8 sec.) causes lighting
dimming (to the minimum level).
level memory
tiME
The device after press-
ing the push-button
switches on according
to the adjusted time
(tp), then it switches off
automatically. Another pressing of
the push-button during time count-
down causes the lighting is switched
off before adjusted time finishes.
Default settings - 15 seconds.
CAutioN! Adjusted time cannot
be deleted.
REMotE CoNtRoLS DELEtioN
tiME PRoGRAMMiNG
level
memory
CooPERAtioN AND oPERAtiNG RANGE
Symbol
RoP-01 RoP-02 RoB-01 SRP-02 SRP-03 RWG-01 RWL-01 RoM-01 RoM-10 RDP-01 RtN-01
RNK-02
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNK-04
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
P-256/8
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
P-257/4 (2)
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNM-10
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
RNP-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNP-02
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNL-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
RtN-01
200 m
200 m
200 m
200 m
200 m
250 m
200 m
250 m
250 m
200 m
250 m
RCR-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
Rti-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RXM-01
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
* - 1-channel transmitters do not cooperate with roller blind controllers.
CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between a transmitter and a receiver,
it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%,
glass: from 10 to 20 %, over- and underground medium and high electrical power lines, radio and television transmitters, GSM transmitters set close to a device system have
also a negative influence on the range.
level
memory
level
memory
level
memory
level
memory
level
memory
tRANSMittERS
RECEiVERS
RNK-02
2–channel button
radio transmitter
RNL-01
Radio
foot transmitter
RoP-01
1-channel
radio receiver
RWL-01
Radio lighting
switch
RNK-04
4-channel button
radio transmitter
Rti-01
IR/EXTA FREE
transceiver
RoP-02
2-channel
radio receiver
RWG-01
Remote control
socket
P-256/8
8-channel
remote controller
RNM-10
4-channel radio
modular transmitter
RDP-01
1-channel
radio dimmer
SRP-02
Radio roller blinds
controller
P-257/4
4-channel
remote controller
RNP-01
4-channel
radio transmitter
RoB-01/12-24V
Radio
gate controller
SRP-03
Central radio roller
blinds controller
P-257/2
2-channel
remote controller
RNP-02
4-channel
radio transmitter
RoM-01
1-channel radio
modular receiver
RoM-10
2-channel
radio modular receiver
RCR-01
Radio
motion sensor
RXM-01
Translator
RS-485/EXTA FREE
ACCESSoRiES
ANt-01
External antenna
RtN-01
Retransmitter
Maximum time is 18 hours.
Press RNK-04
transmitter’s
push-button for
a longer time.
Press PROG push-button of RDP-01 device
for a longer time until LED red diode switches on
(constant signal). Next release PROG push-button.
Press PROG push-button of RDP-01 device for
a longer time until LED red diode switches on
(constant signal). Next release PROG push-button.
Press PROG push-button of RDP-01 device
for a longer time until LED red diode switches on
(constant signal). Next release PROG push-button.
Press PROG push-button of RDP-01 device for
a longer time till LED red diode switches on
(constant signal). Next release PROG push-button.
Press the transmitter’s push-button
for a longer time. LED red diode switches
on (first signal pulsates,
next the signal is constant).
Press and release transmitter’s first
push-button. LED red diode switches on
(first signal pulsates,
next the signal is constant).
Release transmitter’s push-
button. LED red diode switches
on (first signal pulsates,
next the signal is constant).
Press the same transmitter’s push-
-button and release it. LED red diode
switches on (the signal pulsates) and
next it switches off -
THE TRANSMITTER IS ADDED.
CoMFoRt
mode:
oNE PuSH-ButtoN
mode:
SWitCH oN/SWitCH oFF
mode (two push-buttons):
tiME
mode (one push-button):
CAutioN: Every transmitter can cooperate with RDP-01 in a different mode, depending on how they were added to the device.
one transmitter can be added during one programming cycle. Full memory is signalled with pulsating LED red diode.
Press and release the second transmitter’s
push-button. LED red diode switches on
(the signal pulsates) and next it switches
off - THE TRANSMITTER IS ADDED.
Release transmitter’s push-button. LED red
diode switches on (the signal pulsates), next
the LED red diode switches off - it means
the TRANSMITTER IS ADDED.
Press and then release transmitter’s
push-button.LED red diode switches on
(first signal pulsates,
next the signal is constant).
Press and release the same transmitter’s
push-button. LED red diode switches on
(signal pulsates) and then switches off -
THE TRANSMITTER IS ADDED.
After the adjusted time is
finished (the number of LED
red diode flashes) press
PROG push-button and then
release it - TIME IS ADDED.
Press PROG push-button of RDP-01
device and then release it. LED red diode
switches off and then switches on
(signal pulsates). Every LED diode pulse
equals 1 second.
Press PROG push-button of RDP-01 device for a longer time till
LED red diode switches on (constant signal). Next release PROG
push-button. Wait (for about 5 seconds) till LED red diode switches
on (first signal pulsates, next the signal is constant).
Press PROG push-button of RDP-01
device for a longer time.
After 5 seconds LED red diode switches on
(signal pulsates) and then it switches off.
Release the push-button in RDP-01 -
MEMORY IS DELETED.
1s 2s
ns
0%
95%