FOUR CHANNEL TRANSMITTER RNM-24
OPERATION MANUAL
ZAMEL
Sp. z o.o.
ul. Zielona 27, 43-200 Pszczyna, Poland
tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04
www.zamel.com
, e-mail: [email protected]
plik: RNM-24_inst_ext_gb | modyfikacja: 30.05.2018
Connect the device to
single-phase mains, ac-
cording to applicable
standards. The connec-
tion method is shown in
this manual. The activities
related to the installation,
connection and adjust-
ment should be performed by qualified elec-
tricians, familiar with the user manual and
functions of the device. Removing the hous-
ing leads to the loss of guarantee and cre-
ates the risk of electric shock. Before starting
installation, ensure connection lines are not
supplied with voltage. For installation, use a
Philips screwdriver with a diameter of up to
3.5 mm. The correct operation of the device
can be affected by transport, storage and
operation. Installing the device is not recom-
mended in the following cases: no compo-
nents, damage to the equipment or deformi-
ties. In the event of malfunctioning, contact
the manufacturer.
CAUTION
APPEARANCE
FEATURES
TECHNICAL DATA
DESCRIPTION
● Radio transmitter for installation in switch-
gears using TH35 bar.
● remote control for EXTA LIFE system receiv-
ers;
● capable of independent control of up to four
circuits (channels);
● encrypted RF transmission
● 230 V AC power supply;
● long operating range (up to 350 m in open
areas),
● Removable antenna, enabling the connec-
tion of an external antenna.
The RNM-24 transmitter enables wireless
control of EXTA LIFE system receivers. It is de-
signed to implement such functions as turning
on/off the lighting, adjusting illumination, clos-
ing/opening roller shutters and garage doors.
For installing in switchgears using TH35 bar.
The transmitter has four inputs triggered with
230 V AC voltage. It is triggered by a short-term
closing of a specific input using phase voltage
or neutral cable voltage. The transmitter ena-
bles independent control of up to four circuits
/ channels. With built-in LEDS indicating the
transmission and operation status of different
inputs. The RF transmission is encrypted for
increased control security.
RNM-24
Rated supply voltage: 230 V AC
Supply voltage tolerance: -15 ÷ +10 %
Rated mains frequency: 50 / 60 Hz
Rated power consumption: 0.4 W
Operating range: max. 350 m in open areas
Transmission: RF, ISM 868 MHz (868.50 MHz)
Method of transmission with system components: one-way, 9600 bps
Encryption: 128-bit key algorithm
Channels: 4
Optical signalling of transmission: green LED
Optical indication of input activity: 4 × red LED
Compatible connectors: monostable (buttons) / bistable (switches)*
Number of termination points: 8
Connecting cable cross-section: Up to 2.5 mm
2
Operating temperature range: -10 to +55 °C
Enclosure protection rating: IP20
Dimensions: 90 × 35 × 66 mm (two module housing)
Weight: 0.09 kg
Reference standards: PN-ETSI EN 300 220-1, PN-ETSI EN 300 220-
2, PN-EN 60669, PN-EN 60950, PN-EN 61000
* typically, IN1 ÷ IN4 inputs are designed to work with monostable connectors (normally open) — the transmitter sends
information upon short triggering of any input. The transmitter inputs are suitable for working with bistable connectors
(long-lasting application of phase voltage or neutral cable to the transmitter input is possible). However, it is neces-
sary to consider the operation of the transmitter with this kind of connectors (if possible, the transmitter should be
programmed with the receiver in the so-called monostable mode). In this mode, the receiver is turned on as long as
the given input is triggered.
CAUTION! The transmission range is specified to open areas, which are perfect transmission conditions with-
out obstacles. If there are the following obstacle types between the transmitter and the receiver, expect the
transmission range to be reduced by 10 to 40% for brickwork, 5 to 10% for wood and drywall, 40 to 80% for
reinforced concrete, 90 to 100% by metal, and 10 to 20% by glass. The transmission range is also adversely
affected by overhead and underground high-voltage power lines and GSM transmitter bases located near the
devices.
The symbol means selective
collecting of electrical and electronic
equipment. It is forbidden to put the
used equipment together with other
waste.
Signalling LED: green
power supply/transmission)
Signalling LEDs - 4x red LED
(IN1 ÷ IN4 inputs status)
Antenna socket
IN1 ÷ IN4 control inputs
Extra power supply terminals L’,N
(required for correct operation of actuation
system)
Power terminals
