ZALMAN FX100 User Manual Download Page 2

1

.COM

2. Specifications

1. Precautions

1) Do not ingest the Thermal Grease, and avoid its contact with skin and eyes.

     If contact is made with skin, wash off with water. If ingested or irritation

     persists, seek medical attention.

2) To prevent possible injuries, gloves must be worn while handling this product.

3) Excessive force exerted on the fan may cause damage to the fan and/or

     system.

4) Use and keep product away from reach of children.

5) Check the components list and condition of the product before installation.

     If any problem is found, contact the retailer to obtain a replacement.

6) During transportation of the system, the cooler must be removed. Zalman

     is not responsible for any damages that occur during the transport of a system.

7) Product design and specifications may be revised to improve quality and

     performance.

FX100

Material

Pure Aluminum & Copper

Weight

770g

Dimensions

156(L) x 156(W) x 157(H)mm

Noise Level

0dBA

Thermal 

Grease

[ZM-STG2M]

Capacity

1g

Temperature

Range

-40°C ~ +150°C (-40℉ ~ +302℉)

                             

Model

     Spec.

Disclaimer)  Zalman Tech Co., Ltd. is not responsible for any damages due to 

external causes, including but not limited to, improper use, problems with 

electrical power, accident, neglect, alteration, repair, improper installation, 

or improper testing.

Summary of Contents for FX100














Reviews: