INSTALLATION
INSTRUCTIONS
Determine the position where you would
like to place the mirror (for best results,
locate a stud).
Unscrew mounting plate from the mirror
to locate mounting holes and mark hole
locations on the wall.
Use a
⅛
” drill to make a 1” deep hole at
the marks.
Install the mirror plate over the mounting
bracket and secure with two nuts.
Be sure the mirror is attached securely
before using.
1
2
3
5
4
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical appliance, basic precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS
APPLIANCE
DANGER
To reduce the risk of electric shock:
• Always unplug this appliance from the electrical
outlet before cleaning.
WARNING
To reduce the risk of burns, fire, electric
shock, or injury to persons:
• Unplug from outlet before putting on or taking off parts.
• Close supervision is necessary when this appliance is used
by, or near children, or disabled persons.
• Use this appliance only for its intended use as described in
this manual. Do not use attachments not recommended by
the manufacturer.
• Never operate this appliance if it has a damaged cord or
plug, if it is not working properly, if it has been dropped
or damaged, or dropped into water. Return unit to
manufacturer for examination and repair.
• Keep the cord away from heated surfaces.
• Never operate the unit with the air openings blocked. Keep
the air openings free of lint, hair and the like.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Never operate where aerosol (spray) products are being
used, or where oxygen is administered.
• To disconnect, turn all controls to off position, then remove
plug from outlet.
• Do not use an extension cord with this appliance.
• As with any product containing glass and chemicals,
reasonable care should be observed when burned out
lamps are discarded. Unbroken lamps should never be put
into fire, domestic incinerators, or trash compactors.
Note: The fluorescent bulb should last over five times
longer than regular bulbs. In case that it needs to be
replaced, contact Zadro Product’s Customer Service
for instructions.
• Be sure mirror is not in a position where it can reflect
sunlight. Reflected sunlight can cause fire.
SAVE THESE INSTRUCTIONS
USER MAINTENANCE INSTRUCTIONS
LIGHT BULB REPLACEMENT
To replace the light bulb, place the mirror face down
on a flat surface and follow these steps:
1. Unplug the power cord from the outlet.
2. Remove the three screws as well as the washers
and save them.
3. Carefully, remove the backplate from the mirror’s
frame by slowly lifting it upward while holding the
frame down.
4. Disconnect the power supply wires to the ballast
by unplugging the two connectors.
5. Remove the 4-prong plug attached to the bulb
by moving the back of it from side to side, while
pulling it outwards.
6. You will notice the three light bulb posts that
have soft sticky back tape applied to them. They
center and protect the light bulb inside the acrylic
frame. Gently remove the old light bulb by pulling
it outwards.
DO NOT
squeeze or press against
the light bulb - it is made of very thin glass and will
break easily. Lift
ONLY
by the plastic connector
attached to the bulb.
7. Install the new light bulb by following the above
procedure in reverse.
8. You
MUST
only use a 22W circular fluorescent
bulb. The use of a stronger/lighter bulb may
present a possible fire hazard and will void the
warranty.
Model
Description
QTY
Cost
P129
22W White Light Circular
Fluorescent Bulb, 10,000 Hour
$10.00
CA Residents Add Tax
$0.78
Add S/H
$6.00
To order, call customer service at (800) 468-4348 or visit our
website at
www.zadroproducts.com
THIS PRODUCT IS PROVIDED WITH A POLARIZED
PLUG. AS A SAFETY FEATURE, THIS PLUG WILL FIT
IN A POLARIZED OUTLET ONLY ONE WAY. IF THE
PLUG DOES NOT FIT, REVERSE THE PLUG. IF IT STILL
DOES NOT FIT, CONTACT A QUALIFIED ELECTRICIAN.
NEVER USE AN EXTENSION CORD. DO NOT ATTEMPT
TO DEFEAT THIS SAFETY FEATURE.
POLARITY TEST
DIELECTRIC VOLTAGE WITHSTAND TEST
INSPECTED BY: ________________________
PASSED
PASSED
NOT REQ.
