Z3 Technology Z3-DME-03 User Instructions Download Page 43 | Manualshive

Page: 43 / 54

background image

DOC-USR-0061-03

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

43

9.0

SUMMARY OF OPTIONS

This section lists the different options that are available in the various menus.

9.1

The System Setup Tab

Parameter

Options (default in bold)

Notes

Local IP Address

192.168.x.y

(192.168.81.07)

Sets the IP address of the Z3-DME-03. Note that a
“save” of these settings and a reboot is needed for
changes to this value to take effect.

Local Netmask

255.255.z.w (

255.255.0.0

)

Sets the netmask of the Z3-DME-03. Note that a
“save” of these settings and a reboot is needed for
changes to this value to take effect.

Default Gateway 192.168.a.b (

192.168.0.1

)

Sets the network gateway to use for the Z3-DME-03.
Note that a “save” of these settings and a reboot is
needed for changes to this value to take effect.

DNS Server IP 1

a.b.c.d (8.8.8.8)

Specifies the primary DNS server to be used for
hostname lookup when in static IP mode. When in
DHCP mode, DNS information is acquired from the
DHCP server.

DNS Server IP 2

e.f.g.h (8.8.4.4)

Specifies the secondary DNS server to be used for
hostname lookup when in static IP mode. When in
DHCP mode, DNS information is acquired from the
DHCP server.

Use DHCP

Checked

Unchecked

Sets whether DHCP is used. See Section 6.10, “
Running DHCP” on page 24 for more details.

Set Device Name

Sets the name for the Z3-DME-03.

Set Password

Sets the system password. See Section 8.3, “ Using
the Password Feature” on page 41 for more details.

update device firmware

See Section 8.2, “ Making a Firmware Update” on
p.39 for details.

download device logs

Clicking this causes the Z3-DME-03 to extract a set
of diagnostic logs that can be sent to Z3 Technology
in the event of an issue to be reported. This file is
saved on the PC which the GUI is being run from.

«
...
41
42
43
44
45
...
»

Summary of Contents for Z3-DME-03























































Reviews:

No comments

Related manuals for Z3-DME-03

Brand: Patton electronics Pages: 16

Brand: Danfoss Pages: 36

Brand: 3onedata Pages: 3

Brand: Meicheng Pages: 8

EQUINOX EQX 10000-2T

Brand: Salicru Pages: 24

Brand: SAJ Pages: 26

Brand: Lika Pages: 2

BLUESTREAM DA44AU

Brand: Dante Pages: 12

Brand: Cerwin-Vega Pages: 12

Brand: My Cable Mart Pages: 4

Brand: EBARA Pages: 34

Scan Converter VSC 500

Brand: Extron electronics Pages: 2

RAKK DAC Mark II

Brand: Raleigh Audio Pages: 9

Brand: ZIPPER MASCHINEN Pages: 52

Brand: SKP Pro Audio Pages: 20

Brand: Soarland & Hexin Pages: 2

Brand: Microcare Pages: 35

Brand: Pulse-Eight Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands