Z3 Technology Z3-DME-01 User Instructions Download Page 7

Page: 7 / 39

CONFIDENTIAL

DOC-USR-0018-09

____________________________________________________________________________________

Z3 Technology, LLC

♦

100 N. 8th St. STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

4.0

FEATURES

The Z3-DME-01 is a high definition, low-cost, network-enabled media encoder with the following features:



HD resolutions up to 1920x1080 including 1080i, 1080p30 and 720p



Supported video includes H.264 and MPEG-2



Standard Definition encoding for ISDB-T, DVB-H, and other standards



Low latency encode mode



Video Inputs: HD-SDI, Composite



Input video resizer supports many standard resolutions



Video Output Interfaces: Ethernet and ASI



Outputs RTP, RTMP, or MPEG-2 Transport Stream



Supports fractional resolutions and frame rates



Video Frame Rate: 50Hz or 60Hz



Supports extraction of closed caption data from composite input or SDI input



SD Card interface for local storage and firmware updates



Web-based configuration software for user-friendly configuration and control



RS-232 serial port for optional technical configuration and control



Operating Temperature: 0 to 40 degrees C at 20-80% relative humidity (non-condensing)



Storage Temperature: -40 to 70 degrees C at 20-80% relative humidity (non-condensing)



Measurements: 186 x 123 x 29 mm (7.32 x 4.84 x 1.14 in)



Weight: 722 g (1.59 lb)

4.1

Supported Input Resolutions- Encode

SDI:

1080p30, 1080i30, 1080i29.97, 1080i25, 1080720p60, 720p59.94, 720p50, 576i25, 480i30,
and 480i29.97. Also supports 23.98Psf input for all resolutions.

Composite: 576i25, 480i30, and 480i29.97

Summary of Contents for Z3-DME-01








































Search results

Summary of Contents for Z3-DME-01

Reviews:

Related manuals for Z3-DME-01

Brands by name

Popular brands

Z3 Technology Z3-DME-01, User Instructions

Search results

Summary of Contents for Z3-DME-01

Reviews:

Related manuals for Z3-DME-01

Brands by name

Popular brands