Z3 Technology Z3-DM816X-RPS RDK User Manual Download Page 54

Page: 54 / 67

CONFIDENTIAL

DOC-USR-0026-02

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

DM816X-RPS RDK.

9.6

The CH2 Tab

(Please see CH1 values – Encode/Decode for a detailed explanation)

9.7

Values Appearing at the Bottom of All Tabs

Parameter

Options (default in bold)

Notes

preset

serial_menu

encoder factory default

(any user-defined profiles)

The configuration file to use.

serial_menu = Last value saved in GUI

encoder factory default = Factory settings

Can also add more profiles by clicking on
“new” in the User Presets tab.

Save

Click on this to save preset value to what was
selected.

Operating Mode

Encoder Interlaced/Progressive

Encoder Single HD

Decoder

“Encoder Interlaced/Progressive” and
“Decoder” can be used to select between
encode and decode. “Encoder Single HD” is
deprecated and does not apply to this release.

Stop All

Stop encode on all channels.

Start All

Start encode on all channels.

Summary of Contents for Z3-DM816X-RPS RDK




































































Search results

Summary of Contents for Z3-DM816X-RPS RDK

Reviews:

Related manuals for Z3-DM816X-RPS RDK

Brands by name

Popular brands

Z3 Technology Z3-DM816X-RPS RDK, User Manual

Search results

Summary of Contents for Z3-DM816X-RPS RDK

Reviews:

Related manuals for Z3-DM816X-RPS RDK

Brands by name

Popular brands