Z3 Technology Z3-DM816X-RPS RDK User Manual Download Page 53

Page: 53 / 67

CONFIDENTIAL

DOC-USR-0026-02

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

start

Start encode session.

update

Can be used to change the bit rate without
stopping/restarting an encode session (see
Section 5.10, “Changing the bit rate
dynamically,” on page 26).

clone

Duplicate CH tab (can be used to quickly
copy CH1 values to CH2, for example).

delete

Used to delete excess tabs created by Clone.

(status)

IDLE, STOPPED, RUNNING,
POLLING

Current status of the encoder. “POLLING”
indicates “start” was pressed and the
encoder is waiting for valid input data to be
detected.

Note 1: Input Resolutions Supported:

WQVGA (320x180), QVGA (320x240), SIF (352x240), CIF (352x288), 2-CIF (352x576), 640x360,

VGA (640x480), 4-CIF (704x576), 16:9 PAL (1024x576), D1 PAL (720x576), D1 NTSC (720x480),

720p (1280x720), XGA (1280x1024), 1080p (1920x1080)

Note 2: GOP Sizes Supported:

10, 12, 15, 25, 30, 50, 60, 100, 120, 200, 240 frames

9.5

The CH1 Tab -- Decode

Parameter

Options (default in bold)

Notes

Input Interface

RTP

UDP

TSFILE

FILE

Where to get the input bitstream. “RTP”
and “UDP” will get the stream from the
Ethernet interface. TSFILE and FILE are not
supported in this release.

Address

x.y.z.w

(225.1.2.3)

The URL the bitstream is being sent to.

Port

0-9999 (

5004

)

The port the bitstream is being sent to.

Audio

Off

Determines whether audio is decoded /
played for this bitstream.

Output Port

Auto

HDMI

If audio is selected, use to select the audio
output. Only HDMI is supported for the

Summary of Contents for Z3-DM816X-RPS RDK




































































Search results

Summary of Contents for Z3-DM816X-RPS RDK

Reviews:

Related manuals for Z3-DM816X-RPS RDK

Brands by name

Popular brands

Z3 Technology Z3-DM816X-RPS RDK, User Manual

Search results

Summary of Contents for Z3-DM816X-RPS RDK

Reviews:

Related manuals for Z3-DM816X-RPS RDK

Brands by name

Popular brands