Z3 Technology HE4K-DCK-10 User Instructions Download Page 11

Page: 11 / 76

HE4K-DCK-10 User Instructions

DOC-USR-0123-01

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

5.0

GETTING STARTED WITH THE HE4K-DCK-10

If you have received an HE4K-DCK-10 assembly, you will need to connect it to the Sony FCB-ER8300 4K
camera block. The Interface Front End PCB of the HE4K-DCK-10 assembly (see

Figure 4

) has a 30-pin KEL

connector that allows a flexible ribbon cable to be used to connect the encoder assembly to an identical
connector on the Sony FCB-ER8300.

The KEL cable is sold separately (ordering part number: CBL-0025-01).

WARNING: ONLY USE THE CORRECT KEL RIBBON CABLE PROVIDED BY Z3 TECHNOLOGY.

Using an incorrect cable can permanently damage the camera body.

Figure 4 HE4K-DCK-10 Physical Block Diagram (Camera Not Included)

Figure 5 HE4K-DCK-10 Connected to FCB-ER8300 (Camera Not Included)

Sony FCB ER-8300

(Not Included)

KEL Ribbon Cable

(Sold Separately)

Summary of Contents for HE4K-DCK-10













































































Search results

Summary of Contents for HE4K-DCK-10

Reviews:

Related manuals for HE4K-DCK-10

Brands by name

Popular brands

Z3 Technology HE4K-DCK-10, User Instructions

Search results

Summary of Contents for HE4K-DCK-10

Reviews:

Related manuals for HE4K-DCK-10

Brands by name

Popular brands