Z3 Technology EUS Z3-MVE-150 User Instructions Download | Manualshive

Page: 64 / 79

background image

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

64

9.5

The CH1 Tab (Encode)

An asterisk (

*

) denotes a field available in Advanced Settings Mode. See Section 8.3 to access these

fields.

Parameter

Options (default in bold)

Notes

Encoder Setup

Video Source

HDMI1

HD-SDI

The input source for channel 1 is

HDMI only.

An SDI source is only supported by using the
channel 2 tab.

HD-SDI selection supports HD-SDI and 3G-SDI
resolutions.

16:9

Checked

Unchecked

For any SD resolutions (NTSC, PAL), checking
this forces the aspect ratio to be “16:9” in
the output (otherwise a default value of 4:3
is used). This value is ignored for HD
resolutions.

Video Resolution

Follow Input

176x144 – 1920x1080

The encode resolution for channel 1. If this
resolution is different from the capture
resolution, resizing will occur. “Follow
Input” generates the resolution based on the
capture resolution (see Note 1 for
resolutions supported).

Video Bitrate

100 – 12000K (

8000K

)

Textbox for entering video bitrate. For
example:

1M = 1,000,000 bits per second

1000K = 1,000,000 bits per second

2.5M = Not a Valid Format

Video Rate Control

VBR

CBR

Selects the encoder rate control mechanism.
VBR (Variable Bitrate) means that the
encoding bitrate can fluctuate within the
bitrate statistical period. CBR (Constant
Bitrate) means that a stable encoding
bitrate is ensured within the bitrate
statistical time.

Video Profile

*

High

The H.264 profile of the bitstream.

«
...
62
63
64
65
66
...
»

Summary of Contents for EUS Z3-MVE-150
















































































Reviews:

No comments

Related manuals for EUS Z3-MVE-150

Brand: Tvone Pages: 16

Brand: Wavecrest Pages: 39

Brand: QUAD Pages: 38

Brand: Q CELLS Pages: 11

Brand: Miteq Pages: 55

Power WHISPERWATT DCA-45SSIU2

Brand: MULTIQUIP Pages: 160

HDMI Encoder 8x

Brand: NetUP Pages: 44

Brand: Bticino Pages: 12

Brand: Caliber Pages: 52

Brand: Nextar Pages: 38

Brand: Urrea Pages: 12

Brand: ENFORCER Pages: 4

Brand: AJA Pages: 43

Brand: Intellinet Pages: 16

maintenance and

Brand: Dometic Pages: 28

Brand: Daktronics Pages: 21

Brand: OutBack Power Pages: 4

Brand: StarTech.com Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands