Z-Wave ST814 Owner'S Manual Download Page 8

 

8

Specifications 
 

Operating Frequency 

868.42MHz (ST814-1) / 908.42MHz (ST814-2) 

Operating Temperature Range 

-10

 ~ 50

 

Relative Humidity Range 

20% ~ 90% 

Temperature Unit 

℃ / ℉ 

Battery Type 

1.5V x 3 Alkaline/AA type battery 

Operating Range 

Up to 30 meters line of sight (indoor) 

ZDK Version 

V5.02 

*Specifications are subject to change without notice                    

A501111451R01 

 

 

   

 

 

                                   

 

 

Federal Communication Commission Interference Statement 

 
This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC Rules.    These limits are designed 
to provide reasonable protection against harmful interference in a residential 
installation.  This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications.  However, there is no 
guarantee that interference will not occur in a particular installation.  If this 
equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one of the following measures: 
 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that to which 
the receiver is connected. 

Consult the dealer or an experienced radio/TV technician for help. 

 
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, 
and (2) this device must accept any interference received, including interference 
that may cause undesired operation. 

 

FCC Caution: Any changes or modifications not expressly approved by the party 
responsible for compliance could void the user's authority to operate this 
equipment. 

 

This transmitter must not be co-located or operating in conjunction with any 

other antenna or transmitter.

 

WARNING: 

 
Do not dispose of electrical appliances as unsorted municipal waste, use 
separate collection facilities.   
 
Contact your local government for information regarding the collection systems 
available. 
 
If electrical appliances are disposed of in landfills or dumps, hazardous 
substances can leak into the groundwater and get into the food chain, damaging 
your health and well-being. 
 
When replacing old appliances with new once, the retailer is legally obligated to 
take back your old appliance for disposal at least for free of charge. 

Summary of Contents for ST814









Reviews: