background image

2
4

 

 

Regulatory information

 

FCC ID : M7N-BW8290 

FCC Compliance Statement 

This device complies with Part 15 of the FCC rules. Operation is 
sub-  ject to the following two conditions: 
•  This device may not cause harmful interference, and 
•  This device must accept any interference received, including 

inter-  ference that may cause undesired operation. 

This  equipment  has  been  tested  and  found  to  comply  with  the 
lim-  its  for  a  Class  B  digital  device,  pursuant  to  Part  15  of  the 
FCC  Rules.  These  limits  are  designed  to  provide  reasonable 
protection  against  harmful  interference  in  a  residential 
installation.  This  equipment  generates,  uses  and  can  radiate 
radio  frequency  energy  and,  if  not  installed  and  used  in 
accordance  with  the  instructions,  may  cause 

harmful 

interference  to  radio  communications.  However,  there  is  no 
guarantee  that  interference  will  not  occur  in  a  particular 
installation.  If  this  equipment  does  cause  harmful  interference 
to  radio  or  televi-  sion  reception,  which  can  be  determined  by 
turning the equipment  off and on, the user is encouraged to try 
to  correct  the  interference  by  one  or  more  of  the  following 
measures: 
•  Reorient or relocate the receiving antenna. 
•  Increase the separation between the equipment and receiver. 
•  Connect the equipment into an outlet on a circuit different 

from  that to which the receiver is connected. 

•  Consult the dealer or an experienced radio/TV technician for 

help. 

 

Notice  :  Changes  or  modifications  to  this  unit  not  expressly 

approved  by  the  party  responsible  for  compliance  could  void 

the user authority to operate the equip-  ment.

 

Summary of Contents for AC MASTER LITE




























Reviews: