background image

2

 

 

SAFETY INSTRUCTION 

 

IMPORTANT SAFETY INSTRUCTIONS 

 

Read, follow and keep these instructions. 

 

Heed all warnings. 

 

Do not use this apparatus near water. 

 

Clean only with dry cloth. 

 

Do not block any ventilation openings. Install in accordance with the manufacturer’s 
instructions. 

 

Do not install near any heat sources such as radiators, heat registers, stoves, or other 
apparatus (including amplifiers) that produce heat. 

 

The parameter of the using power source should be accordance with which indicating 
on the rear panel; otherwise the machine will work improperly and even be ruined. 

 

Protect  the  power  cord  from  being  walked  on  or  pinched  particularly  at  plugs, 
convenience receptacles, and the point where they exit from the apparatus. 

 

Only use attachments/accessories specified by the manufacturer. 

 

To prolong the useful life of this machine, the interval of the continuous switch action 
must be above one minute. 

 

Use only the cart, stand, tripod, bracket, or table specified by the manufacturer, or 
sold  with  the  apparatus.  When  a  cart  is  used,  use  caution  when  moving  the 
cart/apparatus combination to avoid injury from tip-over. 

 

Unplug  this  apparatus  during  lightning  storms  or  when  unused  for  long  periods  of 
time. 

 

Refer  all  servicing  to  qualified  service  personnel.  Servicing  is  required  when  the 
apparatus  has  been  damaged  in  any  way,  such  as  power-supply  cord  or  plug  is 
damaged,  liquid  has  been  spilled  or  objects  have  fallen  into  the  apparatus,  the 
apparatus  has  been  exposed  to  rain  or  moisture,  does  not  operate  normally,  or  has 
been dropped. 

 

Warning:  This  unit  should  only  be  serviced  by  an  authorized  and  properly  trained 
technician. Opening the cover or other attempts by the user to service this unit may 
result in serious injury or death from electrical shock, and may increase the risk of 
fire. 

 

The MAINS plug or an appliance coupler of the apparatus is used as the disconnect 
device, the disconnect device shall remain readily operable. 

 

The signal cable must be earthed to the system. 

 

No naked flame sources, such as lighted candles, should be placed on the apparatus. 

Note: 

All the OSD and illustrations in this manual may be somewhat different from the 

actual situation. Please take the actual RECEIVER as the standard. 

WARNING: 

To reduce the risk of fire or electric shock, do not expose this product to 

rain or moisture. Apparatus shall not be exposed to dripping or splashing and no objects 
filled  with  liquids,  such  as  vases,  shall  be  placed  on  the  apparatus.  Refer  to  the 
identification/rating  label  located  on  the  back  panel  of  your  product  for  its  proper 
operating voltage. 
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. For 
applicable power supplies see user instructions 

Summary of Contents for IHO-2000 I












Reviews: