background image

10 

 

CHECKLIST FOR INSPECTION 

 

Owner:  

Date: 

 

 

 
Tested unit:  

Serial number  

 

 

o

  Firmware has been updated to current version. 

o

  Nuts and tilting units of the ST16S have been tested. 

o

  The motor shafts and propellers are in good condition. 

o

  The battery packs are properly installed and snap into place. 

o

  The landing gear is in a good condition, and is properly extended and retracted. 

o

  The camera has been installed and is in good condition. 

o

  The camera rails are in good condition. 

o

  The LED indicators have been checked. 

o

  The telemetry function works and the data recorded with it is correct. 

o

  The commissioning sequence is normal. 

o

  The accelerometer has been successfully tested. 

o

  Compass calibration was checked. 

o

  The GPS signal has found and detected enough satellites. 

o

  The stationary floating test was carried out. 

o

  The image acquisition was tested from above. 

o

  The function and quality of the camera have been tested. 

o

  How good the response of the aircraft is in manual mode or without GPS was 

tested. 

o

  The WayPoint / Survey function has been tested. 

o

  RTL and automatic landing have been tested. 

o

  GPS was retrieved during flight. 

o

  It has been tested whether the motors and the battery have a normal 

operating temperature. 

o

  The video / image recordings were examined for discrepancies. 

o

  The device was cleaned. 

 

 
Maintenance performed by:  

Date:  

 

 

Remarks: 

Summary of Contents for H520














Reviews: