Yunca Gas LEEDZ Installation & Operation Manual Download Page 12

Revised 04-08-10 

 

YUNCA Leedz FS Fuzzy Feb 2010 

 

 

 

Page 12 of 19

MAINTENANCE

 

(cont) 

 
CLEANING THE GLASS 

 
The glass may be cleaned with damp paper towels. Ceramic glass cook top cleaner may also be 
used. The inside of the glass may also need cleaning from time to time (refer page 11 for glass 
door removal information). 

Note: Never clean the glass when it is hot. Do not use abrasive cleaners on the glass. 
 

CLEANING THE CHASSIS 

 

The enamelled chassis may need cleaning from time to time to remove a white film (refer page 
11 for glass door removal information). The chassis is enamelled so a wipe over with a damp 
cloth, when the chassis is cool, will be sufficient. 

 

 

REPLACING THE DOOR ROPE (GASKET) 

                                                                                          
The YUNCA 

LEEDZ

 (Fuzzy Logic control) has a 10mm fibreglass gasket (1608LF) surrounding 

the front and side glass. Should it ever need replacement, use only the replacement gasket that 
is available from your YUNCA dealer.  

 
Procedure: 

1. Remove the front door as described on previous page. 
 
2. Remove the existing gasket and clean the channel of all loose material. 
  
3. Lay a thin bed of gasket cement (PVA glue) around the length of the channel 
 
4. Lay the gasket in the channel ensuring the gasket is not stretched. 
 
5. Replace the door carefully to avoid dislodging the gasket. 
 
 

BATTERY BACK UP REPLACEMENT 

 
Your 

YUNCA GAS LEEDZ

 (Fuzzy Logic control) will operate (WITHOUT FAN BOOST) if power 

is not available for any reason.  
 
Two “D” size batteries are located on the right side plinth panel. Unclip the cover from the top, (it 
is hinged at the base), and remove the batteries, replacing with fresh ones. The cover shows the 
polarity of the batteries. 
 
Take care when working near an operating heater, it will be hot!  
 
Batteries will operate the back up system for about 200 hours. Fan boost cannot run on battery 
back up.  
 

Always  ensure  the  batteries  are  fresh

,  and  consider  changing  these  once a  year  (end  of 

summer daylight saving time, when you change your smoke alarm batteries, is a good routine. 
You will have fresh batteries for the coming winter). Batteries left too long may leak and damage 
the contacts, so take note of the recommendation to change them annually. 
 

Summary of Contents for LEEDZ




















Reviews: