YSI ProSample P User Manual Download Page 5 | Manualshive

Page: 5 / 70

YSI ProSample P User Manual Download Page 5

5

Reference relevant section of this manual for operation and/or safety
information

Appears on the outside of the peristaltic pump cover. This cover
should not be open while the instrument is on, as the user can be
seriously injured if they are exposed to moving parts in the peristaltic
pump assembly.

Safety Information

Please read this entire manual before unpacking, setting up or operating this equipment. Pay attention to all
precautionary statements. Failure to do so could result in serious injury to the operator or damage to the equipment.
Make sure that the protection provided by this equipment is not impaired. Do not use or install this equipment in any
manner other than that specified in this manual.

A

A

NOTICE:

The manufacturer is not responsible for any damages due to misapplication or misuse of this

product including, without limitation, direct, incidental and consequential damages, and disclaims
such damages to the full extent permitted under applicable law. The user is solely responsible to
identify critical application risks and install appropriate mechanisms to protect processes during a
possible equipment malfunction.

NOTICE:

Indicates a situation which, if not avoided, may cause damage to the instrument

Precautionary Symbols in the Manual

NOTE:

Information that requires special emphasis

WARNING:

Indicates a potentially hazardous situation which could result in injury

The information contained in this manual is subject to change without notice.

Effort has been made to make the information in this manual complete, accurate, and current.

The manufacturer shall not be held responsible for errors or omissions in this manual.

for the most up-to-date version of this manual.

When viewing this document as an Adobe

TM

PDF, hovering

your cursor over certain phrases will bring up the finger-point
icon. Clicking elements of the Table of Contents, website URLs,
or references to certain sections will take you automatically
to those locations.

THIS IS AN INTERACTIVE DOCUMENT

Precautionary Symbols on the Instrument

«
...
3
4
5
6
7
...
»

Summary of Contents for ProSample P







































































Reviews:

No comments