RX------
A
：
Backlight brightness manual adjustment knob
B
：
Indoor temperature and humidity
C
：
Indoor temperature change trend
D
：
Snooze/ Light button
E
：
Barometric pressure change trend
F
：
Weather forecast pattern
G
：
Barometric pressure value
H
：
Ice alert
I
：
Remote sensor channel number
J: Remote sensor low battery indicator
K
：
Remote sensor temperature alert status symbol
L
：
Remote sensor temperature and humidity
M
：
Projection window
N
：
Indoor comfort indictor
O
：
Day of week
P
：
Alarm clock ON symbol
Q
：
Radio controlled status symbol
R
：
Time
S
：
Automatic backlight brightness symbol
T
：
Date
U
：
Remote sensor comfort indictor
V
：
Light sensor
1
：
Battery cover
2
：
Projection rotation/ON/OFF button
3
：
Remote sensor temperature alert setting button
4
：
Channel button
5
：
MEMORY button
6
：
+/°C /°F button
7
：
-/Alarm ON or OFF button
8
：
ALARM setting button
9
：
General setting button
10
：
Power input jack
11
：
USB charging interface (MAX. 5V1A)
TX------
A1: Remote sensor temperature
A2:
Emission symbols
A3: Channel number
A4: Remote sensor humidity
A5: Remote sensor low battery indicate
B1: °C /°F unit transfer button
B2: Manual transmitter button
B3: Channel switch
C1: Transmit
indicating lamp
C2: Battery compartment cover
C3: Wall mounting hole
C4: Stand cover
C5: Battery compartment
Initial operation
Open the main unit battery compartment cover
Insert CR2032 battery observing polarity (“+” and “ –“ marks), If there is battery insulating sheet, just pull out the insulating sheet.
Insert the output terminal of the adapter into the DC power socket on the back of the product, then insert the adapter into the AC socket (100~240V), the
backlight of the product will always be lit.
The Weather Station will now start to make a connection to the outdoor remote sensor. This process lasts for a maximum of 3 minutes and will displayed by a flashing
reception antenna symbol
in the “OUTDOOR” display area on the receiver.
This now, Open the remote Sensor battery compartment cover, push the channel switch to the “1” position, Insert 2 x AA batteries observing polarity (“+” and “–” marks),
close the battery cover.
If there are multiple outdoor sensor remote controls, according to the same method, push the channel switch to the “2” or “3” position, establish another 2 remote
sensor connections.
After about 3 minutes, it will enter the Radio control receive mode.
The backlight and projection will be temporarily turned off when entering the radio control mode, and will be restored after the reception mode.
Reception of the Radio signal
When entering
MSF
signal receiving mode
，
the icon
starts to flash. When a valid signal is identified, the symbol
will not flash, and the symbol
will
flash.
At 1:00 / 2:00 / 3:00, the clock automatically carries out the synchronization procedure with the
MSF
signal to correct any deviations to the exact time. If this
synchronization attempt is unsuccessful (the icon
disappears from the display), the system will automatically attempt another synchronization at the next full one
hour. This procedure is repeated automatically up to total 5 times.
To start manual
MSF
signal reception, press and hold the “
-
” button for 2 seconds. If no signals received within 7 minutes, then the
MSF
signal search stops and start
again at the next full one hour.
During RC reception
，
to stop searching radio signal, press the “
-
” button once.
：
Received successfully
：
The previous reception was successful, but the last reception failed
：
RCC function is set to OFF
F.Y.I.:
RCC = Radio Controlled Clock.
We recommend the product be placed at a minimum distance of 2.5 meters (8.2Feet) to all sources of interference, such as televisions or computer monitors
or
switching power adapter.
When receiving the
MSF
radio wave, it will automatically turn off the backlight.
Radio reception is weaker in rooms with concrete walls (e.g.: in cellars) and in offices. In such extreme circumstances, place the system close to the window.
During the RC receive mode, only the "
" and “
-
” buttons have a function, other buttons are not functional, If you want to carry out other functions of
operation, please press “
-
” button to exit the RC receiving mode.
Manual time setting
Press the button “
”
to set the clock 12/24Hr format.
