background image

  D A N G E R

It is strictly prohibited for the user to carry out any maintenance or upkeep tasks on the HVAC unit.
This appliance is not destined for use by people (including children) with limited physical, sensorial or

mental capacities, or without adequate experience or knowledge, unless they have received instructions

or been supervised in the use of the appliance by an individual responsible for their safety.
Children must be supervised at all times to ensure that they do not play with the appliance.
Only trained Johnson Controls Inc. personnel with the necessary means and tools may carry out main‐

tenance and upkeep work on the unit.
Trained personnel must be aware of the health and safety regulations and procedures applicable to

HVAC units. They should also be aware of general procedures and those applying specifically to this

unit.
Contact a Johnson Controls Inc. Authorised Technical Assistance Service for scheduled maintenance

on this unit.

PRODUCT DISPOSAL
According to Directive 2002/96/EC of the European

Parliament and of the Council of 27 January 2003, the

presence of the symbol on the product or in the docu‐

ments  included  with  the  product  indicates  that  this

product is classified, according to current law, as an

electrical  and  electronic  device  and,  therefore,  this

product cannot be dealt with at the end of its working

life as domestic or urban waste.
The product must be taken to collection points for the

recycling  of  waste  electrical  and  electronic  equip‐

ment.
The  appropriate  management,  reuse,  assessment

and recycling of these products protect human health

and the environment.

1

User manual

1.3

Regular maintenance activities for which the user is responsible

24

Summary of Contents for YLCA 40



























Reviews: