York YK Style H Operation Manual Download Page 10

Page: 10 / 212

Revision notes

Revisions made to this document are indicated in the following table. These revisions are to

technical information, and any other changes in spelling, grammar, or formatting are not included.

Table 2: Revision notes

Affected pages

Description

8–9

YORK Chiller Access Manager security statement section added

18–19

Access level section updated

19–25

YORK Chiller Access Manager logon instructions added

Global

YORK Chiller Access Manager access levels added to programmable setpoint

information for OptiView screens

Associated literature

Table 3: Associated literature

Manual description

Form number

Variable Speed Drive – Operation

160.00-O1

Solid State Starter – Operation and Maintenance

160.00-O2

Floor Mounted MV SSS – Operation

160.00-O5

Unit Mounted MV SSS – Operation

160.00-O7

Installation – Unit

160.76-N1

Unit Operations and Maintenance

160.76-O1

OptiView™ Control Center – Operation Manual

160.76-O2

Wiring Diagram – Field Connections for YK Chiller (Style H) with OptiView™ Control

Center and Unit-Mounted SSS or Remote Medium Voltage SSS, Medium Voltage

VSD, or Medium Voltage EMS

160.76-PW1

Wiring Diagram – Field Connections for YK Chiller (Style H) with OptiView™ Control

Center and Remote Medium Voltage SSS

160.76-PW2

Wiring Diagram – Field Connections for YK Chiller (Style H) with OptiView™ Control

Center and Remote Medium Voltage VSD

160.76-PW3

Wiring Diagram – Field Control Modifications for YK Chiller (Style H)

160.76-PW4

Wiring Diagram – Model YK (Style H) with OptiView™ Control Center and

Electromechanical Starter

160.76-PW5

Wiring Diagram – Model YK (Style H) with OptiView™ Control Center and SSS with

Modbus, LV VSD with Modbus

160.76-PW6

Wiring Diagram – Field Connections for YK Chiller (Style H) with Low Voltage

Variable Speed Drive

160.76-PW7

Conditioned based maintenance

Traditional chiller maintenance is based upon assumed and generalized conditions. In lieu of

the traditional maintenance program, a Johnson Controls YORK Conditioned Based Maintenance

(CBM) program can be substituted. This CBM service plan is built around the specific needs for

the chiller, operating conditions, and annualized impact realized by the chiller. Your local Johnson

Controls Branch can propose a customized Planned Service Agreement that leverages real time

and historical data, delivering performance reporting, corrective actions required and data enabled

guidance for optimal operation and lifecycle assurance. The program will include fault detection

Model YK Style H Centrifugal Liquid Chillers with OptiView Control Center

Summary of Contents for YK Style H





















































































































































































































Search results

Summary of Contents for YK Style H

Reviews:

Related manuals for YK Style H

Brands by name

Popular brands

York YK Style H, Operation Manual

Search results

Summary of Contents for YK Style H

Reviews:

Related manuals for YK Style H

Brands by name

Popular brands