background image

Do not install the unit drain hose side is too high.

Height A should be less than 5 mm.(Fig.8)

Be sure to arrange the drain hose correctly so that it is

leveled lower than the drain hose connecting port of

the indoor unit. (Fig.7)

Fig.7

OK

NO

NO

Arrange the drain hose

lower than this portion.

Drain hose

Fig.8

A

A

Drain hose

B.  UNDER CEILING TYPE

Using the installation template, drill holes for

piping and anchor bolts(for holes).(Fig.9)

Installation

template

Wall

Ceilling

Drilling position

for piping

Drilling position

for anchor bolt

200m

900m

Fig.9

1.Drilling for piping

   Select piping and drain directions. (Fig.10)

2.Drilling holes for anchor bolts and installing the

   anchor bolts

When the directions are selected, drill 80mm and 50mm

or 150mm dia. hole on the wall so that the hole is tilted

downward toward the outdoor for smooth water flow.

(Fig.11)

Install the drain hose at the rear. It should not be

installed on the top or right side.

Fig. 10

Rear (Install the drain

hose in the direction.)

Right

Fig.13

Fig.12

Insert the anchor bolts into the drilled holes, and drive

the pins completely into the anchor bolts with a hammer.

(Fig.13)

60 to 70mm

12.7mm

Wall

6mm

Fig.11

Installation Procedure

With a concrete drill, drill four 12.7 mm dia. Holes.

(Fig.12)

CAUTION:

CAUTION:

63

Summary of Contents for YHKJXH012BAM--FX


































































































































































Reviews: