background image

5715184-BIM-A-0519

32

Johnson Controls Ducted Systems

DIAGNOSTIC FAULT CODE STORAGE AND 

RETRIEVAL

The control in this furnace is equipped with memory that stores up to
five error codes to allow a service technician to diagnose problems
more easily. This memory is retained even if power to the furnace is
lost. 

This feature must only be used by a qualified service techni-

cian. 

If more than five error codes have occurred since the last reset, only the
five most recent error codes are retained. The furnace control board
has a button labeled LAST ERROR that is used to retrieve error codes.
This function only works if there are no active thermostat signals, so
any call for heating, cooling, or continuous fan must be terminated
before attempting to retrieve error codes. 

To retrieve the error codes, press the LAST ERROR button. The LED
on the control flashes the error codes that are in memory, starting with
the most recent. There is a two-second pause between each flash
code. When the error codes have all been displayed, the LED resumes
the normal slow green flash after a five-second pause. To repeat the
series of error codes, push the button again.

If there are no error codes in memory, the LED flashes two green
flashes. To clear the memory, press the LAST ERROR button and hold
it for more than five seconds. The LED flashes three green flashes
when the memory has been cleared, and resumes the normal slow
green flash after a five-second pause.

SECTION XI: REPLACEMENT PARTS LIST

DESCRIPTION

MOTOR

MOTOR, DIRECT DRIVE BLOWER
BLOWER, COMBUSTION

ELECTRICAL

CAPACITOR, RUN 
SWITCH, LIMIT
CONTROL, FURNACE

IGNITER
SENSOR, FLAME
SWITCHES, PRESSURE
SWITCH, DOOR
TRANSFORMER

VALVE, GAS
CONTROL, TEMPERATURE

AIR MOVING

HOUSING, BLOWER
WHEEL, BLOWER

FABRICATED PARTS

RESTRICTOR, COMBUSTION BLOWER
BURNER, MAIN GAS
BRACKET, IGNITER
SHELF, BLOWER
RAIL, BLOWER (2 required)
BRACKET, BLOWER TRACK (2 required)
HEAT EXCHANGER ASSEMBLY

FABRICATED PARTS CONTINUED

MANIFOLD, GAS
PAN, BOTTOM
PANEL, TOP
PANEL, DOOR (2 required)

PANEL, BLOCKOFF

MISCELLANEOUS

ORIFICE, BURNER (Natural 45)
SIGHT GLASS, OVAL (2 required)
GASKET, FOAM (Door) (1.5 ft required)
PAN, CONDENSATE
BRACKET, DOOR
HARNESS, WIRING
FERRULE (3 required)
GROMMET (3 required)

MOTOR MOUNT

TUBING, SILICON
HOSE, RAIN GUTTER
HOSE, CONDENSATE
PLUG, SEAL, 7/8 in.
PLUG, SEAL, 2-3/8 in.
PLUG, VENT PIPE
BAG, PARTS

KNOB, QUARTER TURN

 (

4 required

)

DIAGRAM, WIRING

DESCRIPTION

REPLACEMENT PART CONTACT INFORMATION

This is a generic parts list. To request a complete parts list, refer to the contact information below.

• Visit our website at www.source1parts.com to do the following:

1. Search for a part or browse the catalog.

2. Find a dealer or distributor.

3. Find Customer Service contact information

a. Click the 

Brand Links

 button.

b. Click the 

Customer Service

 button.

• You can contact us by mail. Send a written request to the following address:

Johnson Controls Ducted Systems

Consumer Relations

5005 York Drive

Norman, OK 73069

Summary of Contents for MM9E Series





































Reviews: