manualshive.com logo in svg

York 160.87-OM1, Operation And Maintenance Manual

The York 160.87-OM1 is a versatile and reliable product designed to simplify your maintenance tasks. With its comprehensive Operation and Maintenance Manual, you'll have all the necessary information at your fingertips. Download this user-friendly manual for free at manualshive.com and ensure optimal performance of your product.

Share
Download
background image

Table 131: Programmable

Button

Access level Description

Winding

Temperature

Protection

Service

Enables the type of temperature sensing device being used to sense

motor winding temperature. When set to any setting other than

Disabled, the respective temperatures are enabled, displayed and

the HIGH WINDING TEMPERATURE Fault and Warning will occur

when the programmed thresholds for those conditions are reached.

The settings are:

•

DISABLED - Disables the Winding Temperature feature. No

winding temperatures are displayed and the heading, text and

data boxes do not appear. The High Winding Temperature

Fault and Warning will not occur. This setting is used when the

motor is not equipped with winding temperature sensors or

if is desired to disable the feature for service reasons. This is

the default setting. The winding displays can be individually

disabled using the Temperature Disable Setpoint (ADMIN

access level) on the MOTOR SETPOINTS Screen.

•

RTD - Enables and displays the 6 (2 per phase) Motor Winding

Temperatures, as reported by the winding RTD's, via the

Motor Monitoring Board serial communications.

•

TRANSMITTER - Enables and displays the 3 Motor Winding

Temperatures, as reported by the winding transmitters via the

Motor Monitoring Board serial communications.

•

VSD TRANSMITTER - Enables and displays the 3 Motor

Winding Temperatures, as reported by the winding

transmitters via the VSD Logic Board serial communications.

Bearing

Temperature

Protection

Service

Enables the type of temperature sensing device being used to sense

motor bearing temperature. When set to any setting other than

Disabled, the respective temperatures are enabled, displayed and

the HIGH BEARING TEMPERATURE Fault and Warning will occur

when the programmed thresholds for those conditions are reached.

The settings are:

•

DISABLED - Disables the Bearing Temperature feature. No

bearing temperatures are displayed and the heading, text

and data boxes do not appear. The High Bearing Temperature

Fault and Warning will not occur. This setting is when if the

motor is not equipped with bearing temperature sensors or if

is desired to disable the feature for service reasons. This is the

default setting.

•

RTD - Enables and displays the 2 motor bearing temperatures,

as reported by the bearing RTD's, via the Motor Monitoring

Board serial communications.

•

VSD TRANSMITTER - Enables and displays the 2 motor bearing

temperatures, as reported by the bearing transmitters via the

VSD Logic Board serial communications.

133

YK-EP Style B Centrifugal Chiller

Summary of Contents for 160.87-OM1













































































































































































































































































Reviews:

No comments

Related manuals for 160.87-OM1

G&D GD-20H Manual & User Manual preview
GD-20H
Brand: G&D Pages: 21
Yard Machines E765F Operator'S Manual preview
E765F
Brand: Yard Machines Pages: 28
Kaysun KEM-30 DRS4 Service Manual preview
KEM-30 DRS4
Brand: Kaysun Pages: 118
Angelo Po BC101LU Use And Installation Manual preview
BC101LU
Brand: Angelo Po Pages: 133
Yardbeast YB2510 User Manual preview
YB2510
Brand: Yardbeast Pages: 23
Troy-Bilt Pro-Line 12183 Parts Catalog preview
Pro-Line 12183
Brand: Troy-Bilt Pages: 16
Troy-Bilt Pro Line Operator'S Manual preview
Pro Line
Brand: Troy-Bilt Pages: 28
Bandit INTIMIDATOR 12XPC Operating & Parts Manual preview
INTIMIDATOR 12XPC
Brand: Bandit Pages: 153
York MILLENNIUM YCAR0315 Installation Operation & Maintenance preview
MILLENNIUM YCAR0315
Brand: York Pages: 160
York YT Millennium Operating & Maintenance preview
YT Millennium
Brand: York Pages: 156
Daikin WDC Installation, Operation And Maintenance Manual preview
WDC
Brand: Daikin Pages: 74
Troy-Bilt 12069 Parts Catalog preview
12069
Brand: Troy-Bilt Pages: 24
Elkay HRC2-5-1C Installation Instructions preview
HRC2-5-1C
Brand: Elkay Pages: 2
MTD 243-650 Operating/Service Instructions Manual preview
243-650
Brand: MTD Pages: 8
White Outdoor RB-530 Operator'S Manual preview
RB-530
Brand: White Outdoor Pages: 20
Verts Loisirs VLRT55 Manual preview
VLRT55
Brand: Verts Loisirs Pages: 60
Thermo Scientific thermoflex Quick Start Manuals preview
thermoflex
Brand: Thermo Scientific Pages: 220
Trane Manhattan Gen II Installation, Operation And Maintenance Manual preview
Manhattan Gen II
Brand: Trane Pages: 82

Brands by name

Popular brands

Load more brands