York Fitness Diamond 45104 Owner'S Manual Download Page 4

PLEASE READ THIS INSTRUCTION MANUAL BEFORE YOU BEGIN ASSEMBLY.  GREAT 

CARE HAS BEEN TAKEN TO DESIGN THESE INSTRUCTIONS AND FOLLOWING THEM 

WILL HELP YOU WITH QUICKER ASSEMBLY AND MINIMISE THE RISK OF INJURY

4

It is important that you keep these instructions for future reference.

!

Safety Information

YOU ARE RESPONSIBLE FOR YOUR OWN SAFETY - 

THIS LIST IS NOT EXHAUSTIVE.
•  Assemble the product on a level surface
•  You will need at least one person to help you assemble this 

unit.

•  Always use the product on a level surface, 

ensure that the product is stable before use.

•  Always ensure that the equipment has adequate space 

on each side and front (the back can be near to a wall).

•  Replace defective components immediately, and/or 

keep the equipment out of use until it is repaired.

•  Use only the adjustment settings as described in the 

instructions.  Always use the correct adjustment pin/fixing.

•  Always check that any pins / fixings are tight and 

secure before use and / or after adjustment. 

•  Never leave any adjustment devices 

projecting from the product.

•  Always consult your doctor before 

undertaking any exercise program.

•  Always wear suitable clothing and footwear 

e.g. tracksuit / shorts / training shoes

•  Remove all personal jewellery before exercising.
•  Ensure you warm-up well before using the 

equipment as this will help to prevent muscle strain.

•  After eating, allow 1-2 hours before exercising as 

this will help to prevent muscle strain.

•  Injuries to health may result from incorrect or 

excessive training.

•  Never overload the equipment - the maximum user load is 

displayed below and on the product label.

•  We recommend that you do not lift weights alone. There 

should be somebody there to assist you.

•  Never use the equipment in any other manner other 

than the ways explained in these instructions and/or 

any wall-chart supplied.

•  Parents and others in charge of children should be aware 

of their responsibility, because the natural play instinct 

and the fondness of experimenting of children can lead to 

situations and behaviour for which the training equipment 

is not intended

•  If children are allowed to use the equipment, 

their mental and physical development and above all 

their temperament should be taken into account. They 

should be controlled and instructed in the correct use 

of the equipment.  

•  The equipment is under no circumstances 

suitable as a children’s toy.

•  Children should not be allowed on, or around 

the equipment - especially when it is not in use.

Safety Standards

This bench meets the requirements of British and EU safety standards EN ISO 20957 parts 1 and 4. 

 

Maximum Weight Limits

Flat / Incline: 

150kg User + 150kg Weight 

This product is not suitable for commercial purposes.

Summary of Contents for Diamond 45104





















Reviews: