manualshive.com logo in svg

YOKOGAWA TB830D, User Manual, Page: 58 / 85

Share
Download
YOKOGAWA TB830D User Manual Download Page 58

  

< 7. Calibration >

7-7

IM 12E01B30-02EN

1st Edition : Mar. 08, 2023-00

(3)  Press on Main screen and go to the calibration menu. 
(4)  On the calibration menu, select Zero calibration. 

(5)  Confirm the reading is stable. Press [check stability]. 
(6)  After the message pops saying the reading is stable, confirm that the calibration value is 

zero. Then press [Next]. 

(7)  Check the result of calibration and press [Accept] to update the Zero of the calibration 

parameter. 

(8)  If Light source has been turned off, turn on the light source. 

 

To shift to the slope calibration, proceed to the steps of “7.6 Slope calibration (Check tool)” 

or “7.7  Slope calibration (Standard solution)”

. If you finish the operation, fix the clear cover 

and feed the sample with the top cover on. Turn off the maintenance mode to end the 

calibration.

7.5 

For zero calibration by turning off the light 

source

This can be selected only when the measured turbidity exceeds 200 NTU.
Refer to “7.4  Zero Calibration” for step.

7.6 

Slope calibration (Check tool)

When you calibrate both zero point and slope, first calibrate the zero point and then the slope. 

See “

l

 Check Tool”

 to confirm about check tool. 

[How to perform Slope calibration-Check tool]

(1)  Turn on the maintenance mode. Drain all the sample inside the Flow cell. Mount the check 

tool referring to “7.2  Turbidity standards”.

(2)  Press on   Main screen and go to the calibration menu.
(3)  On the calibration menu, select [Slope calibration (Check tool)] of turbidity manual calibration.

(4)  Confirm the reading is stable. Press [check stability].
(5)  After the message pops saying the reading is stable, confirm that a value of the check tool is 

correctly displayed. Then press [Next].

(6)  Check the result of calibration and press [Accept] to update the Slope of the calibration 

parameter.

(7)  Remove the check tool. If you finish the calibration, run the sample and turn off the 

maintenance mode.

7.7 

Slope calibration (Standard solution)

Normally slope calibration is performed with a check tool. If you perform with a standard solution, 

follow the steps as below. If you do both Zero and Slope calibration, perform Zero calibration first 

then do Span calibration. Prepare a standard solution referring to “

n

  Turbidity Standards” 

(1)  Make 20 L or more of turbidity standard solution for slope calibration. (see 7.3 to 7.5)

 

Dilute the turbidity standard solution as necessary.

(2)  Turn on the maintenance mode. 
(3)  Press on   Main screen and go to the calibration menu. 
(4)  Select [Slope calibration (standard solution)] on the calibration menu. 

Summary of Contents for TB830D






















































































Reviews:

No comments