YOKOGAWA TA720 User Manual Download Page 57

Page: 57 / 228

3-10

IM 704510-01E

3.6

Calibrating the Probe (Phase Correction)

Items Required

The following items are required.

Compensation Signal

• Frequency:

1 kHz

• Voltage (waveform amplitude):

1 Vp-p

• Waveform type:

Rectangular wave

• Output impedance:

Ω

• Recommended signal:

CAL signal of DL1700 Series Digital Oscilloscope

(YOKOGAWA)

Waveform Monitor

• Frequency characteristics:

DC to 250 MHz (–3 dB point)

• Input coupling:

• Input impedance:

Ω

• Recommended instrument:

DL1700 Series Digital Oscilloscope (YOKOGAWA)

The connection procedure and operation when the recommended signal is connected to

the recommended instruments are described below.

Connecting the instrument

CAUTION

• Do not apply a voltage exceeding the maximum input voltage to the signal input

terminal of the TA720. This may cause damage to the input section.

• Do not apply external voltage to the CAL signal output terminal of the DL1700

Series Digital Oscilloscope or the monitor output terminal of the TA720. This

may cause damage to the internal circuitry.

Check that the TA720 and the DL1700 Series Digital Oscilloscope are turned OFF and

connect them as shown in the figure.

Connect the monitor output terminals on the rear panel of the TA720 (CH A and

CH B) to the signal input terminals of the DL1700 Series Digital Oscilloscope using

BNC cables.

For details on how to use the monitor output of the TA720, see section 13.5, “

Monitor Output.”

Connect the BNC end of the probe to be phase corrected to the signal input

terminal of the TA720.

Connect the other end of probe to the CAL signal output terminal of the DL1700

Series Digital Oscilloscope and the ground wire to the functional ground terminal.

DL1740

Monitor output
terminal

BNC cable

TA720

Signal input
terminal

Phase correction hole

CAL signal output terminal

Functional ground terminal

Summary of Contents for TA720





































































































































































































































Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands

YOKOGAWA TA720, User Manual

Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands