YOKOGAWA ScopeCorder DL950 User Manual Download Page 53

Page: 53 / 316

2-37

IM DL950-02EN

Configuring Data Frame Reading Settings (CAN Port

Configuration)

Tap

CAN Port Configuration

, or press the soft key.

All Sub Channel Setup (All SubChannel Setup - CAN or CAN FD Data

Extraction Conditions)

Tap

All SubChannel Setup

, or press the soft key. The following screen appears.

See “Loading

Definition Files.”

CAN or CAN FD data extraction conditions

Turns sub channels on or off

Set each sub channel’s input to on or off.

See “Port Setup.”

See “Setting All Sub

Channel

Factor/Offset.”

Turns all sub channel on or off

Tap each item. Use the displayed list (options) or input box to set the items.

2.9 Configuring the Monitoring of CAN and CAN FD Bus Signals (/VCE option)

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL950, User Manual

Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands