P.3/3
IM 01W03B02-01EN
5.2 Regulatory Compliance Statements
This product satisfies the following standards.
IMPORTANT
Please check the conditions of use and precautions described in this section. If
it deviates, it may not satisfy the following standard. And please confirm that an
installation region fulfills an applicable standard. If additional regulatory information
and approvals are required, contact a Yokogawa representative.
Radio equipment compliance:
MIC Identification (Japan)
Applied to built-in module.
Construction Design Attestation Number: 006-000927
FCC Approval (United States)
FN120 contains transmitter module as follow;
Contains FCC ID: SGJ-WFC019
FN120 complies with below FCC Rules.
Part 15 Subpart B, Part 15 Subpart C
IMPORTANT
• This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
• FCC CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
• This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter.
NOTE
• Note: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense
• This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines. This equipment should be installed and operated keeping the radiator
at least 20 cm or more away from person’s body.
ISED Approval (Canada)
FN120 contains transmitter module as follow;
Contains IC: 8999A-WIC017
FN120 complies with below standards.
RSS-Gen Issue 5, RSS-247 Issue 2, ICES-003 Issue 7
IMPORTANT
English:
• This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
French:
• L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
NOTE
English:
• This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF)
Exposure rules. This equipment should be installed and operated keeping the
radiator at least 20 cm or more away from person’s body.
French:
• Cet équipement est conforme aux limites d’exposition aux rayonnements
énoncées pour un environnement non contrôlé et respecte les règles d’exposition
aux fréquences radioélectriques (RF) CNR-102 de l’ISDE. Cet équipement doit
être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur
et le corps humain.
RE Directive (EU Countries)
Hereby, Yokogawa Electric Corporation declares that the radio equipment type
FN120 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address:
http://www.yokogawa.com/fld/
The Authorized Representative for this product in the EEA is:
Yokogawa Europe B.V. Euroweg 2, 3825 HD Amersfoort, THE NETHERLANDS.
CE Conformity:
RoHS Directive: EN IEC 63000
RE Directive:
Safety: EN 61010-1, EN 62479
(1) Pollution Degree 2
“Pollution degree” describes the degree to which a solid, liquid, or gas which
deteriorates dielectric strength or surface resistivity is adhering. “2” applies to
normal indoor atmosphere. Normally, only non-conductive pollution occurs.
Occasionally, however, temporary conductivity caused by condensation must be
expected.
(2) Installation Category I
“Overvoltage category (Installation category)” describes a number which defines
a transient overvoltage condition. It implies the regulation for impulse with stand
voltage. “I” applies to electrical equipment which is supplied from the circuit when
appropriate transient overvoltage control means (interfaces) are provided.
(3) Indoor/Outdoor use
It can be used in indoors and outdoors.
(4) Altitude of installation site
Max. 3,000 m above sea level.
Radio Spectrum: EN 300 328
EMC: EN 301 489-1, EN 301 489-17,
EN 61326-1 Class A Table 2, EN 55011 Class A
CAUTION
This instrument is a Class A product, and it is designed for use in the industrial
environment. Please use this instrument in the industrial environment only.
<Information on EU WEEE Directive>
EU WEEE (Waste Electrical and Electronic Equipment) Directive is only valid in the EU.
This instrument is intended to be sold and used only as a part of equipment which is
excluded from WEEE Directive, such as large-scale stationary industrial tools, a large-
scale fixed installation and so on, and, therefore, subjected to the exclusion from the
scope of the WEEE Directive. The instrument should be disposed of in accordance with
local and national legislation/regulations.
Canadian Safety Standards:
CSA C22.2 No.61010-1, CAN/CSA-C22.2 No.94.2-15
(1) Pollution Degree 2
(2) Overvoltage Category I
(3) Altitude (atmosphere pressure): Up to 3000 m
(4) Humidity: 0 to 100%
(5) Electrical supply according to the product ratings
(6) Indoor/Outdoor use, CSA C22.2 No.94 Type 4X
(7) Ambient temperature: –40°C to +85°C
Control of Pollution Caused by the product:
EU RoHS
This product is in conformity with the following standard: EN IEC 63000 (Technical
documentation for the assessment of electrical and electronic products with respect
to the restriction of hazardous substances).
5.3 Model and Suffix Codes
Refer to the General Specification “GS 01W03B02-01EN”.
5.4 External Dimensions and Pin Assignment
Unit: mm (approx. inch)
Pin
Signal
1
Not Connected
2
Signal Ground
3
Power Supply
4
Transmit/Receive Data positive
5
Transmit/Receive Data negative
115 (4.53)
14.3
(0.56)
Ø27
(1.06)
F06.ai
21 (0.83)
Ø23
(0.91)
Plug type of FN120: JR13WPI-5P (connector mating with type of JR13WRI-5S or
JR13WJI-5S)
Revision Record
Title: FN120 Field Wireless Communication Module
Document No.: IM 01W03B02-01EN
Edition
Date
Page
Revised item
1st
Dec. 2021
—
New Publication.
