YOKOGAWA DLM3022 User Manual Download Page 27 | Manualshive

Page: 27 / 284

background image

4-5

IM DLM3054-01EN

Trigger Level (Level)

Trigger level

refers to the signal level used as a reference for detecting a signal’s rising and falling edges or high

and low states. With simple triggers such as the edge trigger, the instrument triggers when the trigger source
level passes through the specified trigger level.
The analog signals (CH1 to CH4) and the logic signal (LOGIC) have different selectable trigger level ranges.

Analog Signals

Selectable range: 8 divisions within the screen
Resolution: 0.01 divisions (for example: 0.02 mV when the time scale is set to 2 mV/division)

Logic Signals (On models with the logic signal input port)

The selectable range varies depending on the logic probe that you use.
• Model 701988: ±40 V (0.05 V resolution)
• Model 701989: ±6 V (0.05 V resolution)

• The trigger level is set using the jog shuttle. If a single trigger source is used (Edge, Pulse Width, Rise/Fall

Time, Runt, Timeout, Window, Interval, FlexRay, CAN, CAN FD, LIN, CXPI, SENT, UART, TV), you can
also use the front-panel LEVEL knob to set the trigger level.

• When the front-panel LEVEL knob is valid, you can press it to automatically set the trigger level.
• If the jog shuttle is controlling the trigger level, you can press the RESET key to reset the trigger level to

the current offset voltage.

• The trigger level is shared between trigger A and trigger B. If the trigger type of one of the triggers has two

levels (upper level and lower level) and that of the other has one level, the center value of the two levels
and the single level are shared.

• The selectable range of threshold levels used to detect logic signal bit states is the same as the selectable

range of the

trigger level. How you can set the bit levels varies depending on the logic probe that

you are using.
Model 701988: The level setting applies to all bits.
Model 701989: The level is set for each bit separately.

• You can also set the level of each bit of the logic signal using Level on the bit setup menu of the LOGIC

key (the level is shared). If you change the level on the trigger menu, the Level value on the bit setup menu
of the LOGIC key will also change.

Trigger Slope (Slope/ Polarity)

Slope

refers to the movement of the signal from a low level to a high level (rising edge) or from a high level to a

low level (falling edge). When a slope is used as one of the trigger conditions, it is called a

trigger slope

.

The following trigger slope settings are available for triggering the instrument.

When the trigger source changes from a level below the trigger level to a

level above the trigger level (rising)

(Slope)
When the trigger source changes from a level above the trigger level to a

level below the trigger level (falling)

(Slope)
When a rising or falling edge is detected

(Slope)
When the trigger source level enters the specified voltage range

(Polarity)
When the trigger source level goes outside of the specified voltage range

(Polarity)

* /

is only selectable when the trigger source is an analog signal.

4 Triggering

«
...
25
26
27
28
29
...
»

Summary of Contents for DLM3022





























































































































































































































































































Reviews:

No comments

Related manuals for DLM3022

Brand: ACS Pages: 56

Brand: Olsen Pages: 56

Brand: Waterous Pages: 5

Brand: 3TECH Pages: 32

Brand: 4EVAC Pages: 15

Brand: Tabi Pages: 8

Brand: Dabi Atlante Pages: 102

SimMan 3G Trauma

Brand: laerdal Pages: 16

Brand: laerdal Pages: 16

Brand: laerdal Pages: 60

Brand: laerdal Pages: 4

Resusci Anne Simulator

Brand: laerdal Pages: 8

Nursing Baby VitalSim

Brand: laerdal Pages: 15

Brand: Raytec Pages: 60

Brand: VDO Pages: 15

Brand: VDO Pages: 20

Brand: Y.I.C. TECHNOLOGIES Pages: 6

R100 Swell Series

Brand: WAVEFIT Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands