YOKOGAWA DL1720E, User Manual

Page: 140 / 186

5-105
IM 701730-17E
Commands
5
:TRIGger:ACTion:MAIL:COUNt
Function Sets/queries the limit for the number of reports
that are sent as an ACTion.
Syntax :TRIGger:ACTion:MAIL:COUNt {<NRf>}
:TRIGger:ACTion:MAIL:COUNt?
<NRf>=1 to 1000
Example :TRIGGER:ACTION:MAIL:COUNT 100
:TRIGGER:ACTION:MAIL:COUNT? ->
:TRIGGER:ACTION:MAIL:COUNT 100
Description Can be used when the Ethernet interface
(option) is installed.
:TRIGger:ACTion:MAIL:MODE
Function Sets/queries whether mail reports are sent as
an ACTion.
Syntax :TRIGger:ACTion:MAIL:MODE
{<Boolean>}
Example :TRIGGER:ACTION:MAIL:MODE OFF
:TRIGGER:ACTION:MAIL:MODE? ->
:TRIGGER:ACTION:MAIL:MODE 0
Description Can be used when the Ethernet interface
(option) is installed.
:TRIGger:ACTion:SAVE
Function Sets/queries whether the waveform data is
saved to the medium at the time of the trigger
action.
Syntax :TRIGger:ACTion:SAVE {<Boolean>}
:TRIGger:ACTion:SAVE?
Example :TRIGGER:ACTION:SAVE ON
:TRIGGER:ACTION:SAVE? ->
:TRIGGER:ACTION:SAVE 1
:TRIGger:ACTion:STARt
Function Starts action-on-trigger.
Syntax :TRIGger:ACTion:STARt
Example :TRIGGER:ACTION:START
Description Use :TRIGger:ACTION:STOP to abort the
trigger action.
:TRIGger:ACTion:STOP
Function Aborts action-on-trigger.
Syntax :TRIGger:ACTion:STOP
Example :TRIGGER:ACTION:STOP
Description This command only aborts the trigger action. It
does not cancel the settings.
The
:TRIGger:ACTION:STARt command can
be used to resume the trigger action.
:TRIGger:ADB? (A Delay B)
Function Queries all A Delay B trigger settings.
Syntax :TRIGger:ADB?
Example :TRIGGER:ADB? ->
:TRIGGER:ADB:DELAY 0.000E+00
:TRIGger:ADB:DELay
Function Sets/queries the delay time for pattern B for an
A Delay B trigger.
Syntax :TRIGger:ADB:DELay {<Time>}
:TRIGger:ADB:DELay?
<Time>=3 ns to 5 s
Example :TRIGGER:ADB:DELAY 1NS
:TRIGGER:ADB:DELAY? ->
:TRIGGER:ADB:DELAY 1.0E-09
:TRIGger:ATRigger?
Function Queries all the pattern A settings.
Syntax :TRIGger:ATRigger?
Example :TRIGGER:ATRIGGER? ->
:TRIGGER:ATRIGGER:CHANNEL1 HIGH;
CHANNEL2 DONTCARE;
CHANNEL3 DONTCARE;
CHANNEL4 DONTCARE;CONDITION ENTER
:TRIGger:ATRigger:CHANnel<x>
Function Sets/queries the channel condition for pattern
A.
Syntax :TRIGger:ATRigger:CHANnel<x>
{DONTcare|HIGH|LOW}
:TRIGger:ATRigger:CHANnel<x>?
<x>=1 to 4 (1 to 2 on the DL1720E)
Example (An example for CH1 is given below.)
:TRIGGER:ATRIGGER:CHANNEL1 HIGH
:TRIGGER:ATRIGGER:CHANNEL1? ->
:TRIGGER:ATRIGGER:CHANNEL1 HIGH
:TRIGger:ATRigger:CONDition
Function Sets/queries the conditions under which pattern
A should become true.
Syntax :TRIGger:ATRigger:CONDition
{ENTer|EXIT}
:TRIGger:ATRigger:CONDition?
Example :TRIGGER:ATRIGGER:CONDITION ENTER
:TRIGGER:ATRIGGER:CONDITION? ->
:TRIGGER:ATRIGGER:CONDITION ENTER
Description This command is valid when the trigger type is
“ABN” or “ADB.”
:TRIGger:BTRigger?
Function Queries all pattern B settings.
Syntax :TRIGger:BTRigger?
Example :TRIGGER:BTRIGGER? ->
:TRIGGER:BTRIGGER:
CHANNEL1 DONTCARE;
CHANNEL2 HIGH;CHANNEL3 DONTCARE;
CHANNEL4 DONTCARE;CONDITION ENTER
:TRIGger:BTRigger:CHANnel<x>
Function Sets/queries the channel condition for pattern
B.
Syntax :TRIGger:BTRigger:CHANnel<x>
{DONTcare|HIGH|LOW}
:TRIGger:BTRigger:CHANnel<x>?
<x>=1 to 4 (1 to 2 on the DL1720E)
Example (An example for CH1 is given below.)
:TRIGGER:BTRIGGER:CHANNEL1 HIGH
:TRIGGER:BTRIGGER:CHANNEL1? ->
:TRIGGER:BTRIGGER:CHANNEL1 HIGH
:TRIGger:BTRigger:CONDition
Function Sets/queries the conditions under which pattern
B becomes true.
Syntax :TRIGger:BTRigger:CONDition
{ENTer|EXIT}
:TRIGger:BTRigger:CONDition?
Example :TRIGGER:BTRIGGER:CONDITION ENTER
:TRIGGER:BTRIGGER:CONDITION? ->
:TRIGGER:BTRIGGER:CONDITION ENTER
Description This command is valid when the trigger type is
“ABN” or “ADB.”
5.30 TRIGger Group