manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

8-16

IM AQ7280-01EN

8.9  Routine Maintenance

Cleaning the Outside of the AQ7280

To clean the LCD or the outside of the AQ7280, turn the power off, and remove the AC adapter from 
the AQ7280. Use a damp, well-wrung cloth to clean the outside and then wipe it off with a dry cloth. 
Do not use chemicals such as thinner, benzene, or alcohol. Doing so may cause deformation and 
discoloring.

Cleaning the Optical Adapter and Optical Fiber End Faces

 WARNING

When cleaning the light emitter, turn off the AQ7280 to prevent the light from accidentally 
being emitted from the light source port. Cleaning the light emitter with the AQ7280 turned 
on may cause the emitted light to accidentally enter the eye. This can cause eye damage or 
vision impairment.

French

 AVERTISSEMENT

Lors du nettoyage de l'émetteur de lumière, mettre l'AQ7280 hors tension pour empêcher 
l'émission accidentelle de lumière provenant du port de la source lumineuse. Le nettoyage 
de l'émetteur de lumière avec l'AQ7280 sous tension peut permettre à la lumière émise de 
pénétrer accidentellement dans les yeux. Ceci peut provoquer des lésions oculaires ou une 
déficience visuelle.

1.

  Check that the AQ7280 is turned off.

2.

  Open the optical port cover.

3.

  Remove the optical adapter.

For the procedure, see section 8.8.

4.

  Use a lens cleaner to clean the optical fiber end face.

5.

  Slowly insert the lens cleaner into the optical connector adapter’s precision sleeve to clean the 

inner walls.

 

  

 

Precision sleeve  

Lens cleaner

If the optical fiber end face is slanted

If the optical fiber end face is slanted, such as on a model with the /ASC option, clean from 

the bottom of the end face upward to prevent the cleaner from tearing or becoming fuzzy 

due to the sharp top edge of the fiber end face.

Edge

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Medeli SP40A User Manual preview
SP40A
Brand: Medeli Pages: 14
Callaway 350TL Manual preview
350TL
Brand: Callaway Pages: 13
ECO Sensors UV-100 User Manual preview
UV-100
Brand: ECO Sensors Pages: 22
ECO Sensors OS-6 User Manual preview
OS-6
Brand: ECO Sensors Pages: 7
F&F LE-01MR v2 User Manual preview
LE-01MR v2
Brand: F&F Pages: 24
Hach PLATINUM Series Manual preview
PLATINUM Series
Brand: Hach Pages: 64
Bartec VOLUTANK Petro 3003 Quick Manual preview
VOLUTANK Petro 3003
Brand: Bartec Pages: 10
QEED QA-POWER-M Instruction Manual preview
QA-POWER-M
Brand: QEED Pages: 6
Metretek MTEK6000 Series User Manual preview
MTEK6000 Series
Brand: Metretek Pages: 81
KALEAS 34058 Operating Instruction preview
34058
Brand: KALEAS Pages: 64
SATO KEIRYOKI 1410-00 Instruction Manual preview
1410-00
Brand: SATO KEIRYOKI Pages: 2
Hanna Instruments HI97730 Instruction Manual preview
HI97730
Brand: Hanna Instruments Pages: 28
BERTHOLD TECHNOLOGIES FlowStar2 LB 514 Operating Manual preview
FlowStar2 LB 514
Brand: BERTHOLD TECHNOLOGIES Pages: 130
Megger CFL535G Quick Start Manual preview
CFL535G
Brand: Megger Pages: 8
A-CUBE USB-1 User Manual preview
USB-1
Brand: A-CUBE Pages: 25
Vanguard Instruments Company TRF-100 User Manual preview
TRF-100
Brand: Vanguard Instruments Company Pages: 111
ZIEHL TR660IP Operating Manual preview
TR660IP
Brand: ZIEHL Pages: 37
XPOtool 63039 Operation Manual preview
63039
Brand: XPOtool Pages: 6

Brands by name

Popular brands

Load more brands