manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

8-13

IM AQ7280-01EN

Troubleshooting, Maintenance, and Inspection

1

2

3

4

5

6

7

8

Index

8.7  Mechanical Inspection and Operation Check

 WARNING

Before performing a mechanical inspection, be sure to turn off the power. Inspecting the 
OTDR port or light source port with the AQ7280 turned on may cause the emitted light to 
accidentally enter the eye. This can cause eye damage or vision impairment.

 CAUTION

•  Connectors clogged with foreign objects can cause abnormal operation or malfunction.
•  Loose connectors may cause the AQ7280 to operate abnormally.
•  If the screws fixing the OTDR unit, OPM/VLS module, or battery cover are loose, the 

AQ7280 may not operate properly.

French

 AVERTISSEMENT

Veiller à couper le courant avant d'effectuer une inspection mécanique. L'inspection du port 
OTDR ou du port de source lumineuse avec l'AQ7280 sous tension peut permettre à la 
lumière émise de pénétrer accidentellement dans les yeux. Ceci peut provoquer des lésions 
oculaires ou une déficience visuelle.

 ATTENTION

•  Si des corps étrangers se retrouvent emprisonnés dans les différents connecteurs, un 

dysfonctionnement ou un endommagement risque de se produire.

•  Si l'ajustement de l'un des différents types de connecteurs n'est pas parfait, l'instrument 

risque de ne pas fonctionner normalement.

•   L'AQ7280 peut ne pas fonctionner correctement si les vis fixant l'unité OTDR, le module 

OPM/VLS ou le couvercle de la batterie sont desserrées.

Mechanical Inspection

Make sure that:
•  The exterior of the AQ7280 is not damaged or deformed.
•  Switches, connectors, and screws are not loose.
•  Switches and moving parts work smoothly.
If there are any problems, contact your nearest YOKOGAWA dealer.

Operation Check

Turn the AQ7280 on to start it. Check the following to verify that the AQ7280 is running normally.
•  The tops screen appears after startup.
•  The screen can be switched using the control keys.
•  Touch panel operations work.

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Hammond Skx PRO Reference Manual preview
Skx PRO
Brand: Hammond Pages: 754
Camille Bauer SIRAX MM1200 Safety Instructions preview
SIRAX MM1200
Brand: Camille Bauer Pages: 12
Eaton Network Card-MS Quick Start Instructions preview
Network Card-MS
Brand: Eaton Pages: 26
LATNEX RF Explorer User Manual preview
RF Explorer
Brand: LATNEX Pages: 55
Laser Technology TruPulse 200X Quick Reference Manual preview
TruPulse 200X
Brand: Laser Technology Pages: 11
Laser Technology TruPulse 200X User Manual preview
TruPulse 200X
Brand: Laser Technology Pages: 62
Veeder-Root TLS-350R Installation Manual preview
TLS-350R
Brand: Veeder-Root Pages: 59
Magnescale DK812S Series Instruction Manual preview
DK812S Series
Brand: Magnescale Pages: 64
Keithley SourceMeter 2430 Service Manual preview
SourceMeter 2430
Brand: Keithley Pages: 141
Aqua Lung PHODS Technical Manual preview
PHODS
Brand: Aqua Lung Pages: 24
FuzzDog Quack Machine Quick Start Manual preview
Quack Machine
Brand: FuzzDog Pages: 6
Chauvin Arnoux AEMC 2139.61 User Manual preview
AEMC 2139.61
Brand: Chauvin Arnoux Pages: 64
S+S Regeltechnik 1101-3121-0049-800 Operating Instructions, Mounting & Installation preview
1101-3121-0049-800
Brand: S+S Regeltechnik Pages: 16
Obvius A90DC-10 Installation And Operation Manual preview
A90DC-10
Brand: Obvius Pages: 15
Hanna Instruments HI 4015 Instruction Manual preview
HI 4015
Brand: Hanna Instruments Pages: 11
Kawai CP95 Owner'S Manual preview
CP95
Brand: Kawai Pages: 36
LI-COR LI-7820 Instruction Manual preview
LI-7820
Brand: LI-COR Pages: 92
Keller LEX 1 Manual preview
LEX 1
Brand: Keller Pages: 8

Brands by name

Popular brands

Load more brands