YOKOGAWA AQ7280 OTDR User Manual Download Page 170 | Manualshive

Page: 170 / 195

background image

7-10

IM AQ7280-01EN

Explanation

You can control an AQ7280 connected to a network from your PC.

Connection Mode

There are two connection modes: Control and View.
Control Mode: The AQ7280 screen is displayed on your PC screen. You can control the AQ7280 with

a mouse or through the touch panel of your PC. You can also download files from the
AQ7280.

View Mode:

The AQ7280 screen is displayed on your PC screen, but you cannot control the
AQ7280 from your PC. You can, however, download files from the AQ7280.

Controlling the AQ7280

If you connect in Control Mode, you can control the AQ7280 from your PC.

Rotary Knob Operation

The operation varies depending on where on the rotary knob you click.
Upper right:   Equivalent to turning the rotary knob to the right by a small amount (1 point).
Lower right:  Equivalent to turning the rotary knob to the right by a large amount (10 points).
Upper left:    Equivalent to turning the rotary knob to the left by a small amount (1 point).
Lower left:    Equivalent to turning the rotary knob to the left by a large amount (10 points).

AQ7280 Touch Panel Operation

The AQ7280 touch panel only supports tapping. You can perform the equivalent of tapping by clicking
the mouse.

Downloading Files

• Only files that are 1400 KB or less in size can be downloaded. The download button does not

appear for files that cannot be downloaded.

• The download destination varies depending on your browser.
• Multiple files cannot be downloaded at once.

7.5 Web Server Feature

«
...
168
169
170
171
172
...
»

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Brand: Farfisa Pages: 14

Brand: Valmet Pages: 63

Brand: T&D Pages: 2

Brand: T&D Pages: 2

Brand: Wagner Meters Pages: 17

Brand: DAKOTA ULTRASONICS Pages: 50

Brand: Jamar Pages: 4

Brand: Endress+Hauser Pages: 88

Brand: SecureAlert, Inc. Pages: 7

Brand: GANN Pages: 89

Brand: Bogen Pages: 14

Brand: Kurzweil Pages: 12

Brand: OHAUS Pages: 6

Brand: SEAWARD Electronic Pages: 57

Brand: Xylem Pages: 39

Micro Alti Vario Plus

Brand: Fairhaven Pages: 20

Brand: Falcon Pages: 25

Brand: R&S Pages: 135

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands