YOKOGAWA AQ2200 Series User Manual Download Page 98

Page: 98 / 183

3.7 Transceiver I/F Module

CAUTION

• Always use the specified connector to connect this module’s I/O terminals. Using

unspecified connectors to connect the I/O terminals may cause damage to the
terminals and the connectors.

• Before connecting cables to or disconnecting cables from the connectors, turn

the output off.

• Do not apply a signal that is greater than the specified maximum input voltage to

an input pin (a pin whose I/O attribute is I) on the SIGNAL connector.

• Make sure that the maximum power consumption for POWER SUPPLY

connector signals PS1 to PS5 is below 28 W.

• Do not apply more than 1 A to a POWER SUPPLY connector pin.

French

ATTENTION

• Toujours utiliser le connecteur spécifié pour le raccordement des bornes d’E/S

de ce module. L’utilisation de connecteurs non conformes aux spécifications
pour le raccordement des bornes d’E/S risque de provoquer des dommages aux
bornes et aux connecteurs.

• Avant de brancher les câbles aux connecteurs ou de les débrancher, mettre la

sortie hors tension.

• Ne pas appliquer de signal supérieur à la tension d’entrée maximum spécifiée à

une broche d’entrée (dont l’attribut d’E/S est E) du connecteur SIGNAL.

• Veiller à ce que la consommation énergétique maximum des signaux de

connecteur POWER SUPPLY PS1 à PS5 soit inférieure à 28 W.

• Ne pas appliquer plus de 1 A à une broche de connecteur POWER SUPPLY.

3-12

IM 735101-01EN

Summary of Contents for AQ2200 Series
























































































































































































Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands

YOKOGAWA AQ2200 Series, User Manual

Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands