YOKOGAWA AQ2200 Series User Manual Download Page 60 | Manualshive

Page: 60 / 183

background image

2.1 Handling Precautions

Safety Precautions

If you are using this instrument for the first time, make sure to thoroughly read the safety
precautions given on pages vi to xi.

Do Not Remove the Case

Do not remove the case from the frame controller. Some parts of the instrument use high
voltages and are extremely dangerous. For internal inspection and adjustment, contact
your nearest YOKOGAWA dealer.

Unplug If Abnormal Behavior Occurs

If you notice smoke or unusual odors coming from the instrument, immediately turn off
the power and unplug the power cord. Then, contact your nearest YOKOGAWA dealer.

Do Not Damage the Power Cord

Nothing should be placed on top of the power cord, and it should be kept away from any
heat sources. When removing the plug from the power outlet, do not pull on the cord.
Pull from the plug. If the power cord is damaged or if you are using the instrument in a
location where the power supply specifications are different, purchase a power cord that
matches the specifications of the region that the instrument will be used in.

Operating Environment and Conditions

This instrument complies with the EMC standard under specific operating environment
and operating conditions. If the installation, wiring, and so on are not appropriate, the
compliance conditions of the EMC standard may not be met. In such cases, the user will
be required to take appropriate measures.

General Handling Precautions

Do Not Place Objects on Top of the Instrument

Never place objects such as other instruments or objects that contain water on top of the
instrument. Doing so may damage the instrument.

Do Not Damage the LCD

Because the LCD is very vulnerable and can be easily scratched, do not allow any sharp
objects near it. Also, the LCD should not be exposed to vibrations or shocks.

Unplug during Extended Non-Use

Unplug the power cord from the outlet.

Chapter 2 Making Preparations for Measurements

2-1

IM 735101-01EN

Making Preparations for Measurements

1

2

3

4

5

Index

«
...
58
59
60
61
62
...
»

Summary of Contents for AQ2200 Series
























































































































































































Reviews:

No comments

Related manuals for AQ2200 Series

Brand: Yamaha Pages: 69

Brand: Bamo Pages: 8

Brand: Hach Pages: 28

Brand: Kathrein Pages: 10

NANOCOLOR Advance

Brand: Macherey-Nagel Pages: 45

Brand: Mahr Pages: 384

Brand: Velleman Pages: 96

Brand: jenway Pages: 52

Brand: Keeler Pages: 68

Brand: Magnescale Pages: 64

SourceMeter 2430

Brand: Keithley Pages: 141

Brand: Endress+Hauser Pages: 88

Brand: Oldham Pages: 96

Brand: Guru Home Systems Pages: 20

Brand: Vectronics Pages: 2

Brand: Resol Pages: 24

Brand: ICP DAS USA Pages: 71

Brand: CONDTROL Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands