Yitong Technology YTMC-51N1-M2B User Manual Download Page 14

Bonded MoCA 2.0 Network 

 

 

Coaxial Cable

 

If applicable, the coaxial cable screen shield needs to be connected to the Earth  
at the building entrance per ANSI/NFPA70, the National Electrical Code (NEC), 
in particular Section 820.93, “Grounding of Outer Conductive Shield of a 
Coaxial Cable,” or in accordance with local regulation. 

FCC Class B Equipment

 

This equipment has been tested and found to comply with the limits for a Class  
B digital device, pursuant to Part 15 of the FCC Rules. These limits are  designed 
to provide reasonable protection against harmful interference in a  residential 
installation. This equipment generates, uses and can radiate radio  frequency 
energy and, if not installed and used in accordance with the  instructions, may 
cause harmful interference to radio communications. However,  there is no 
guarantee that interference will not occur in a particular installation.   If this 
equipment does cause harmful interference to radio or television  reception, 
which can be determined by turning the equipment off and on, the  user is 
encouraged to try and correct the interference by implementing one or  more of 
the following measures: 

 

Reorient or relocate the device; 

 

Increase the separation between the equipment and receiver; 

 

Connect the equipment to an outlet on a circuit different from that to which 
the receiver is connected (applicable only to power line products); 

 

Consult the dealer or an experience radio or television technician for help. 

Declaration of Conformity for Products Marked with 

the FCC logo–USA Only

 

This device complies with Part 15 of the FCC Rules license-exempt RSS 
standard(s). Operation is subject to the following two conditions: 
1.

 

This device may not cause harmful interference; 

2.

 

This device must accept any interference received, including 
interference that may cause undesired operation of the device. 

Modifications

 

The FCC requires the user to be notified that any changes or modifications 
made to this device that are not expressly approved by Jiangsu Yitong high- 
tech Co., Ltd. may void the user’s authority to operate the equipment. 

13 

 

Summary of Contents for YTMC-51N1-M2B
















Reviews: