manualshive.com logo in svg

YILKAR YH COMFORT, Operating Instructions Manual

Share
Download
YILKAR YH COMFORT Operating Instructions Manual Download Page 28

Cause: Occlusion may occur on the air intake side or the outlet side during operation. There may be a
detection problem with the flame monitoring or overheating sensor.
Device Response: If the device is working when it detects this error, it will switch to stop mode by
cooling.
Troubleshooting:
* Make sure there is no blockage in the air intake and outlet of the device.
* After making sure of these situations, reset the device from the button or disconnect the system from
the power supply and connect again.

E 20 : Air Blockage Failure

Cause: YHC fault may have occurred.
Device Response: If the device is working when it detects this error, it will switch to stop mode by
cooling.
Troubleshooting: Replace YHC. After replacement, reset the device from the button or disconnect
the system from the power supply and connect again.

E 21 : EEPROM Failure

Cause: If the system is operated in room thermostat mode, there may be a malfunction of the
temperature sensor on the control unit.
Device Response: If the device is working when it detects this error, it will switch to stop mode by
cooling.
Troubleshooting:
* Replace the control unit.
* After replacement, reset the device from the button or disconnect the system from the power supply
and connect again.

E 20 : Control Unit Temperature Sensor Failure (Opsiyonel)

11. Technical information

The Control Unit is designed for Engine, Diesel Fuel Pump and Glow Plug 12 V and 24 V. 
Control Panel and temperature sensor components are not voltage dependent.
Permissible ambient temperatures

Operation: –40 ° C to +40 ° C
Storage: –40 ° C to +90 ° C

Diesel fuel specified by the manufacturer according to DIN EN590 should be used. The use of additives
has no known adverse effects. If fuel is taken from the vehicle tank, follow the additional instructions
provided by the vehicle manufacturer.

Attention !
The installation instructions must be read and followed carefully before installing the heater
and operating the device. Regulations will be invalid and YILKAR will not take any
responsibility if improper installation or work is done or determined to be done.

28

Summary of Contents for YH COMFORT

































Reviews:

No comments

Brands by name

Popular brands

Load more brands