Use the machine, the following basic measures should abide, avoid electric shock
or cause injury or damage caused by fires.
1. To ensure personal safety, after the machine completed work, please turn off
the main power switch, and unplug the power cord if long time no use.
2. You must use the original approval or recommendation of the parts, otherwise
it will lead to serious consequences.
3. Machine failure must be by professionals or the company designated
personnel for repair.
4. This product is grounded three-wire plug, must be inserted within the three-
hole grounded outlet, do not change the plugs or use ungrounded three
adapter made it bad grounded.
5. Hot air gun or soldering station is open, its temperature are likely to reach
400°C. Do not use it near flammable gas, objects. Tube and the heat emitted
very hot, can burn the body, do not touch the hot pipe and direct injection to
heat the human body.
6. Before hot air gun turned on, please ensure it is in safety environment, do not
leave the jobs site.
7. When the hot air gun opening do not install nozzle, the heat pipe and the
nozzle must be cooling. Then installed the other nozzle.
8. After use, the machine need to cool down when packing.
9. Do not use a soldering iron to weld outside the work; Do not iron percussion
table to clear the residual flux, this could seriously damage the iron.
10. The machine welding will take smoke, please do proper ventilation.
5
6
1. If the supply cord is damaged, it must be replaced by a special cord or
assemble available from the manufacturer or its service agent.
2.
WARNING:
This tool must be placed on its stand when not in use.
3. Be careful when using the appliance in places where there are combustible
materials; Do not apply to the same place for a long time.
4. Be aware that heat may be conducted to combustible materials that are out of
sight; Do not leave the appliance unattended when it is switched on.
5. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge. Unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
I
. Tip Maintenance And Use
Tip temperature
High soldering temperature can degrade the tip. Use the
lowest possible soldering temperature. The excellent
thermal recovery characteristics ensure efficient and effec-
tive soldering even at low temperatures. This also protects
the solder de items from thermal damage.
Cleaning
Clean the tip regularly with a cleaning sponge. As oxides and
carbides from the solder and flux can form impurities on the
tip. These impurities can result in defective joints or reduce
the tips heat conductivity. When using the soldering iron
continuously, be sure to loosen the tip and remove all oxides
at least once a week. This helps prevent seizure and
reduction of the tip temperature.
When not in use
Never leave the soldering iron sitting at high temperature
foe long periods of time, as the tip’s solder plating will
become covered with oxide, which can greatly reduce the
tip’s heat conductivity.
After use
Wipe the tip clean and coat the tip with fresh solder.
1. When soldering iron is used for the first time, you should pay attention to mon-
itor iron tip warming situation, wait until the temperature just melted tin wire, a
layer of tin on the part of the gold-plated iron tip,and then the temperature was
raised to the required temperature. Keep in mind when working iron tip should
be long-term with a layer of tin to protection iron tip,in order to achieve optimal
soldering function.
2. As an oxide layer on the surface of iron tip, resulting in false low temperature
soldering iron tip, unable to melt tin and the tin, in fact, at this time the heating
elements with the soldering iron is high temperature state. This happens situ-
ation not to blind the temperature rises again, the application of clean sponge
clear oxides, such as not clear, please turn off the power, soldering iron be dr-
opped to room temperature, with No.0 sandpaper accidentally cleared the
oxide, then repeat the operation of the first point iron initial use.
3. Please pay more attention soldering iron in high temperature work back into
iron holder, should be adjust temperature button below 250°C stand - by use,
stand-by time over 20 minutes, please turn off power. Otherwise the soldering
iron in a high temperature for long time. Because between iron holder and
soldering iron generate accumulated temperature, lead to heating elements
accelerated aging, soldering iron tip derivative oxide, directly weakened sold-
ering, severe will result in the connecting screw nut plastic melt of the handle
or heating elements short circuit.
4. If the tip deformation or the occurrence of heavy erosion, to replace the new
one. (Note: Do not use knife file remove oxides of soldering iron tip.)
5. Soldering, do not give iron tips too much pressure, this will not change the
thermal conductivity, otherwise will lead to iron tip damage.
Safety Rules
Warning!!!
