Yeti SB4.5C User Manual Download Page 17

34.

WARRANTY

YETI LIMITED (5) FIVE YEAR FRAME WARRANTY  
(applies to SB4.5c / SB5c / Beti SB5c / SB5+ / SB5.5c / SB6c / ASRc / Beti ASRc) 
Yeti Cycles will repair or replace, at its option, any frame it determines to be defective due to 

defective materials and/or workmanship. The (5) one year limited warranty is conditioned upon 

the bicycle being ridden under normal conditions and having been properly maintained. This 

warranty does not apply to the components attached to the frameset such as suspension 

components, wheels, drive train, brakes, seatpost, handlebar and stem. This warranty applies 

only to the original owner and is non-transferable. This warranty is void if the bicycle was not 

properly assembled by an authorized Yeti dealer.

ADDITIONAL CONDITIONS 
These limited warranties do not apply to normal wear and tear, nor to claimed defects, 
malfunctions or failures that result from abuse, neglect, improper assembly, improper 
maintenance, alteration, collision, crash or misuse. The original owner shall pay all labor 
charges connected with the repair or removal of all components. Under no circumstance does 
this limited warranty include the cost of travel or shipment to and from an authorized Yeti dealer. 
In order to exercise your rights under these limited warranties, the bicycle or frameset must be 
presented to an authorized Yeti dealer, together with proof of purchase.

*The above warranties have been in effect since January 2012. For warranty information on Yeti

 

frames sold prior to that date please consult your local authorized dealer.

NO FAULT REPLACEMENT POLICY 
Yeti Cycles will make replacement parts available at a minimum charge to the original owner in 
the event of a crash or any other non-warranty situation. Yeti Cycles does this at its sole 
discretion and reserves the right to refuse this offer.

PRODUCT LIFE CYCLE 

Every YETI frameset has a useful product life cycle.  The length of that useful product life cycle 

will vary depending on the construction and the materials of the frameset, maintenance and 

care the frameset receives , and the amount and type of use the frameset is subjected to over 

its life. YETI recommends that an authorized YETI dealer should inspect the  frame for stress  

annually. Frame stress could cause potential failure and the signs are usually apparent in the 

form of cracks, fracture lines, deformation, dents, and any other visual indicators of 

abnormality. These safety checks for frame stress are important to prevent accidents, injury to 

the cyclist, and product failure of a YETI frameset.

DISCLAIMER 
YETI Cycles is not responsible for any damages to you or others arising from riding, 
transporting or other use of your bicycle. In the event that your frame breaks or malfunctions, 
YETI Cycles shall have no liability or obligation beyond the repair or replacement of your 
frame pursuant to the terms outlined in the warranty.

*If you have a warranty concern, please contact your authorized Yeti dealer.

YETI CYCLES 
621 Corporate Circle, Unit B 
Golden, CO 80401 
(p) 303-278-6909
(f) 303-278-6906
www.yeticycles.com

BUSINESS HOURS 

Monday-Friday  

8AM-11:30AM, 1:00PM-5:30PM  

(Mountain Time)

Summary of Contents for SB4.5C


















Reviews: